EGR FIT-FF1028 Summit Series Fender Flares Instruction Manual

EGR FIT-FF1028 Summit Series Fender Flares

Product Information

The Summit Series Fender Flares Toyota Tundra (22-ON) FIT-FF1028 is a set of fender flares designed specifically for the Toyota Tundra model year 2022 and onwards. The fender flares are made from high-quality materials to provide durability and protection for your vehicle. The package includes all the necessary hardware, such as extrusion, alcohol wipe, attachment clips, long screws, and spacers, for installation. The fender flares are designed to match the profile of the vehicle and come into contact with specific areas of the vehicle body.

Before painting and installing the product, it is important to thoroughly inspect all components listed in the tables provided in the user manual. Test fitment should also be done prior to painting and installation. If there are any fitment questions or missing components, it is recommended to contact EGR Inc. for assistance. To prevent damage, the product should not be exposed to temperatures above 70°C (158°F) during baking, and the extrusion and hardware should not be fitted to the fender flares until the paint is completely dry.

Product Usage Instructions

Install Preparation

Step 1: Attach the included rubber seal to all four fender flares. Peel back two adhesive backings and position the seal on the fender flare. Attach the seal by peeling back a few inches at a time and applying pressure to secure it to the fender flare edge. Attach the rubber seal along the top leading edge of the fender flare where it contacts the vehicle body. Trim the rubber seal at the end of each fender flare. Save any extra rubber seal for installation on the opposite side fender flare and discard any excess once both sides are complete.

Important Note: Trim the rubber seal.

Front Fender Flare Installation

Step 2: Using a 10mm socket/wrench, remove the factory screw locations (X8) as noted in the user manual and retain them for re-installation.

Step 3: Clean the body areas where the fender flares will contact the vehicle surface. Ensure that the fenders are dry prior to installation.

Step 4: Hold the fender flare on the vehicle in the position of best fit. Note where the marked slots in the fender flare align with the existing mounting holes on the vehicle. Remove the fender flare.

Step 5: Secure the attachment clips by sliding them into the fender flare slots. Use the factory screws that were previously removed to attach the clips into the corresponding existing holes in the upper inner splashguard. Do not fully tighten the screws at this stage.

Step 6: Using the factory screws that were previously removed, loosely screw them into the slotted hole locations. Once all factory screws have been re-installed, apply pressure and begin to tighten them in the order shown in the user manual. Ensure that the rubber seal is sitting flat against the vehicle. Once satisfied, fully tighten all screw locations in the above order.

This completes the installation for the front driver side. Repeat the steps for the front passenger side. For Technical Support/Warranty Information, please call 800-757-7075 or contact EGR Inc. at 4000 East Greystone Drive, Ontario, CA 91761.

Important: Please read instructions entirely before installing this product.

Hardware Included

Ensure that both left- and right-hand Fender Flares suit the profile of the vehicle. Please take note of the areas where the Fender Flares comes into contact with the vehicle.

PRIOR TO ANY PAINTING & INSTALLATION, PRODUCT SHOULD BE THOROUGHLY INSPECTED FOR ALL COMPONENTS LISTED IN THE TABLES ABOVE. PRODUCT SHOULD ALSO BE TEST FITTED PRIOR TO ANY PAINTING & INSTALLATION. PLEASE CONTACT EGR INC. IF YOU HAVE ANY FITMENT QUESTIONS AND OR MISSING COMPONENTS.

PAINTING INSTRUCTIONS

If Fender Flares are being painted; do not install edge extrusion until painting is complete. Prior to painting, clean all surfaces to be painted using clean water and a mild detergent, do not use lacquer thinner or any solvent-based products. Wipe completely dry. Best results will be achieved by wiping the areas to be painted with a tack rag just prior to painting. Most automotive paints can be applied directly to the Fender Flares; however, some may require a primer (check paint manufacturer specifications). Good adhesion will be achieved without sanding. Select a paint (and primer if necessary) that is suitable for rigid plastics PMMA (Acrylic). If using a paint system that requires baking, do not expose the product to temperatures above 70°C (158°F). Do not fit the extrusion or any of the hardware to the Fender Flares until the paint is completely dry.

INSTALL PREPARATION

STEP 1

Attach the included rubber seal to ALL (4) Fender Flares. Peel back 2” of the adhesive backing and position on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Ensure pressure is used to secure rubber seal to Fender Flare edge. Attach rubber seal along the top leading edge of the Fender Flare where it contacts the vehicle body. Trim rubber seal at end of each Fender Flare. Save extra rubber seal for install on opposite side Fender Flare and discard any excess once both sides are complete.

IMPORTANT NOTE: Trim rubber seal

FRONT FENDER FLARE INSTALLATION

• STEP 2: Using a 10mm socket / wrench remove factory screw locations (X8) where noted above and retain for re-install.

• STEP 3: Clean the body areas where the Fender Flares will contact the vehicle surface. Ensure fenders are dry prior to install.

• STEP 4: Hold Fender Flare on the vehicle in the position of best fit. Note where above marked slots in the Fender Flare align with the existing mounting holes on the vehicle. Remove the Fender Flare.

• STEP 5: Secure attachment clips by sliding clip into Fender Flare slot. Using the factory screws that were previously removed, attach the clips into corresponding existing holes in upper inner splashguard.
  Do not fully tighten screws at this stage.

• STEP 6: Using factory screws that were previously removed begin to loosely screw into slotted hole locations. Once all factory screws have been re-installed, apply pressure and begin to tighten in the order shown above. Ensure rubber seal is sitting flat against vehicle. When satisfied fully tighten all screw locations, in the above order in which they were just installed.

  • This completes the installation for the front driver side, repeat steps for front passenger side.

REAR FENDER FLARE INSTALLATION

• STEP 7: Using a 10mm socket / wrench remove factory screw locations (X4) where noted above and retain for re-install.

• STEP 8: Using the alcohol wipes supplied, clean the body area where the Fender Flares will contact vehicle surface. Ensure fender surface is dry prior to install.

• STEP 9: Hold Fender Flare on the vehicle in the position of best fit. Note where all the slots in the Fender Flare align with existing mounting holes on the vehicle. Make note of position (A) as it will require hardware in the kit supplied. All remaining positions will re-use factory screws.

• STEP 10: Begin to loosely install factory screws into the corresponding factory attachment points. Once all factory screws have been re-installed, begin to fasten in the order shown above. Do not fully tighten screws at this time.
  POSITION (A) requires the long screw and spacer supplied in kit.

• STEP 11: POSITION (A) – Ready the spacers (and long screw) to go in behind the Fender Flare to fill the gap between the flare and the vehicle.

• Begin to tighten all (4) positions in the same order noted in Step 10. This completes the installation for the rear driver side, repeat steps for rear passenger side.

Contact

• For Technical Support/Warranty Information please call: 800-757-7075
• EGR Inc., 4000 East Greystone Drive, Ontario, CA 91761

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>