PANORAMA SW3-919 Paintwork and Headliner Installation Guide
- June 6, 2024
- PANORAMA
Table of Contents
Installation Instructions
L[G]M[H]M[X]-6-60[-24-58] Series
SW3-919 – v2
Introduction
The Panorama Antennas L[G]MM ‘Great White’ series is trusted around the world
to offer best-in-class LTE performance. The L[G]M[X]M[X]-6-60[-24-58] series
offers a comprehensive range of antennas for vehicular applications requiring
MiMo function for 4G/5G. The antenna range offers a robust, low profile
housing incorporating two ultra-wideband cellular elements supporting 4G and
5G bands, with the fallback capability to 3G/2G.
Versions of the antenna are available with additional 2×2, 3×3 or 4×4 and 6×6
MiMo functions for dual-band WiFi and the LG version incorporates an active
GNSS antenna suitable for use with GPS,
GLONASS, BeiDou, QZSS, and Galileo devices.
Please ensure that you have the correct version before you commence
installation.
Electrical Safety Note
The LG version of this product contains an active GNSS antenna (part number
SR8-JG26NS). Rated voltage: 3-5VDC Rated current: 25mA maximum
The supply to this device must be provided with overcurrent protection of
1A maximum.
Mounting Requirements and Selecting Location
This antenna range does not require a ground plane in order to operate, so
maybe fitted on a metal or plastic roof panel.
When the antenna is to be co-located with other antennas or roof-mounted
equipment, try to achieve a minimum of 30cm (12”) clearance around the L[G]MM
antenna in order to avoid de-tuning and interference issues.
The antenna will fit on a panel up to 9mm (0.35in) thick – extender kit
M18-EXT is available for thicker panels. For the mounting location, select a
flat-panel area to accommodate the 18cm (7.1in) diameter footprint of the
antenna. For curved or ribbed roof panels, the fitting kit LGMM-EXT-R is
available as an accessory item. For temporary magnetic fitment, the magnetic
base SAB-225 is a suitable accessory.
Ensure that it is adequate under panel clearance and that there is no double
skin panel or cross brace present. Measure to check for the central position
if applicable.
Prepare and Drill Hole
Mask the panel area around the hole position to protect the paintwork and headliner. Drill a pilot hole, and then either uses a hole cutter of the correct size or increase the hole diameter to 19mm (3/4”), ensuring that the drill/cutter bit does not contact the internal headliner. Clean area around the hole, carefully removing\ all swarf. Apply some petroleum jelly or paint around the hole to prevent corrosion.
Fitting the Antenna
Note: The adhesive pad provides a means to fixture the antenna and to
prevent rotation during installation it also augments the sealing function of
the antenna to the mounting panel provided by the sealing boot. The
temperature range for optimum pad bonding process is 21°C (70°F) to 37°C
(100°F)
– it is recommended that the installation is not carried out in temperatures
of less than 50°F (10°C).
Remove the protective backing from the underside of the antenna and feed the coaxial cables through the panel. Position the antenna over the hole ensuring correct orientation and stick the antenna to the panel by applying firm downward pressure.
Caution – A slotted/split nut is provided in order to simplify fitting it
over the coaxial cables. When fitting the nut, it is important to ensure that
the cables are held centrally whilst the nut is correctly started on the
threads.
The nut should fit freely by hand and only require a final tighten by a
spanner.
Assemble the nut and washer from the underside and tighten to a recommended
torque of 5Nm (3.6 ft/lbs).
Ensure that the sealing boot is properly compressed.
Routing and Terminating Coaxial Cable(s)
Connect the extension coaxial cables to the antenna and route the cables to the radio equipment.
**** When routing the cables take care to avoid running them adjacent to any existing vehicle wiring or fouling any moving vehicle components. The cables must not be routed in front of an airbag device.
Fit the correct coaxial connectors or adapters to the cables as required.
Commission and Test
- Check the GNSS cable (if applicable):
- Check the GNSS cable with DC to measure high resistance.
- Connect the GNSS cable to the GNSS receiver and check for satellite acquisition.
Check the comms cables:
- Earth continuity: connector body to vehicle ground should measure <0.2Ω (where applicable).
- For LTE elements connector body to center pin should measure low resistance (elements are DC grounded). WiFi elements should measure open circuits using the same test.
- Carry out VSWR check – the VSWR on all feeds should meet the specification in the product data sheet.
- Connect the Cellular/LTE and WiFi cables (if applicable) or secure unused pigtails.
Notices
**| RF Safety Note – Ensure that the antenna is mounted in such a way
that no person is likely to be within a distance of 30cms (12”) from the
antenna during use. Ensure that the antenna is used only as supplied the
coaxial cables should not be cut shorter or otherwise modified.
---|---
**| General Safety Note – Make sure that the product is mounted so
that it cannot fall and cause injury. Do not chew the product or put it in
your mouth. Do not leave children unsupervised with the product or packaging.
| European Waste Electronic Equipment Directive 2002/96/EC Waste
electrical products should not be disposed of with household waste. All
electronic products with the WEEE logo must be collected and sent to approved
operators for safe disposal or recycling. Please recycle where facilities
exist. Many electrical/electronic equipment retailers facilitate the
“Distributor Take-Back scheme” for household WEEE. Check with your Local
Authority or electronic retailers for designated collection facilities where
WEEE can be disposed of for free.
| Directive 2011/65/EU (RoHS 2)
RoHS 2 compliance is declared per Directive 2011/65/EU and its subsequent
amendments with exemption 6. c applied. REACH (Registration, Evaluation,
Authorisation, and Restriction of Chemicals, EC 1907/2006)
This product contains Lead (CAS No. 7439-92-1) which is classified as an SVHC
(Substance of Very High Concern) as being toxic to reproduction under Article
57c. of REACH. Do not chew parts or put them in your mouth, keep away from
unsupervised children. Dispose of parts as WEEE waste do not send to
landfill.
This declaration is issued under the sole responsibility of the manufacturer
The object of the declaration described above is in conformity with the
relevant Union Harmonization
Legislation below:
Directive 2014/53/EU
Radio Equipment Directive (RED)
Harmonised Standards and References:
EN 301 489-1 (V2.1.1): “Electromagnetic compatibility and Radio spectrum
Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 1: Common technical requirements”.
Referencing EN 61000-4-2:2009 – Electrostatic Discharge Immunity and EN
61000-4-3:2006 +A1:2008 +A2:2010 – Radiated RF Immunity
EN 300 440-1 V1.6.1 (2010-08) – Electromagnetic compatibility and radio
spectrum matters (ERM); short range devices; radio equipment to be used in the
1GHz to 40GHz frequency range; Part 1: Technical characteristics and Test
methods in accordance with EN 300 440-2 V1.4.1 (2010-8) – Electromagnetic
compatibility and radio spectrum matters (ERM); short range devices; radio
equipment to be used in the 1GHz to 40GHz frequency range
Low Voltage Directive: Directive 2014/35/EU (Electrical Equipment designed for
use within certain voltage limits) of 26th February 2014.
EN62368-1: 2014 Audio/video, information and communication technology
equipment. Safety requirements
Contact Information
Panorama Antennas Ltd
Head Office – United Kingdom
61 Frogmore, Wandsworth, London, SW18 1HF
sales@panorama-antennas.com
+44 (0)20 8877 4444| Panorama Antennas SAS
France
16 Allée des Acacias, 33700 Mérignac
fr.sales@panorama-antennas.com
+33 554 070 436
---|---
Panorama Antennas Inc
USA
1551 Heritage Parkway, Suite 101, Mansfield, TX, 76063
sales.nam@panorama-antennas.com
+1 817-539-1888| Panorama Antennas
Pte Ltd
Singapore
Space@ Tampines, 18 Tampines Industrial Crescent, 528605
sales.sea@panorama-antennas.com
+65 9155 4194
Panorama Antennas Pty Ltd
Australia
Unit 1, 5 Jaggs Way, Kardinya, WA 6163
sales.apac@panorama-antennas.com
+61 406 812 364| Panorama Antennas Ltd
Germany
de.sales@panorama-antennas.com
+49 2303 902 88 00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>