EGR FF969 Front Bolt-On-Rugged Look Fender Flares Instruction Manual

June 13, 2024
EGR

EGR FF969 Front Bolt-On-Rugged Look Fender Flares Instruction Manual

installation Instructions

Hardware Included QTY
EXTRUSION 25ft
ALCOHOL TOWELETTE 4
SMALL CLIPS 14
SCREWS 6
LARGE U SHAPE CLIPS 6
Bolt Kit Included QTY

ALLEN KEY BOLT
Boil-On look Narre sally)| 42
NUTS| 42
median eye Bekis

Ensure that both left and right hand front Fender Flares suit the profile of the vehicle. Note the areas where the Fender Flares come in contact with the vehicle. NOTE: Before fitting Fender Flares remove any moldings, strips or existing flares from the wheel arch. If there is a body side molding, mark where the molding is to be cut, alternatively the Fender Flare can be cut to go around the molding. Be sure to allow enough room for the extrusion. No drilling of vehicle is required for Bolt-On Look Fender Flares. This is a non- drill product. *For Rugged look flares begin installation at STEP 2. “PRIOR TO ANY PAINTING & INSTALLATION, PRODUCT SHOULD BE THOROUGHLY INSPECTED FOR ALL COMPONENTS LISTED ABOVE. PRODUCT SHOULD ALSO BE TEST FITTED PRIOR TO ANY PAINTING & INSTALLATION. PLEASE CONTACT EGR IF YOU HAVE ANY FITMENT  QUESTIONS AND OR MISSING COMPONENTS.
PAINTING INSTRUCTIONS-It Fender Flares are being painted; do not install edge extrusion until painting is complete. Prior to painting, clean all surfaces to be painted using clean water and a mild detergent, do not use lacquer thinner or any solvent based products. Wipe completely dry. Best results will be achieved by wiping the areas to be painted with at tack rag just prior to painting. Most automotive paints can be applied directly to the Fender Flares, however some may require a primer (check paint manufacturer specifications). Good adhesion will be achieved without sanding. Select a paint (and primer if necessary) that is suitable for rigid plastics PMMA (Acrylic). If using a paint system that requires baking, do not expose the product to temperatures above 70°C (158°F). Do not fit the extrusion or any of the hardware to the Fender Flares until the paint is completely dry.

STEP 1: Attach the 10 bolts and nuts to each Fender Flare using a 3/16″ Allen key and a 10mm.  rench/socket (wrench /socket and Allen key not supplied). Ensure inside of Fender Flares where the rubber seal is attached is clean, using the alcohol wipes provided. Wipe away any residue with a  ry clean cloth.

STEP 2: Attach the included rubber seal to the Fender Flares. Peel back 2″ of the adhesive backing and position on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Ensure pressure is used to secure rubber seal to Fender Flare edge. Attach rubber seal along all areas the Fender Flare will make contact with the vehicle body.

STEP 3: Pulling at right angles to the extrusion, remove the liner from the extrusion in small portions and apply thumb pressure to ensure that it adheres to the Fender Flares.

STEP 4: Trim any unnecessary extrusion and discard.

STEP 5: Clean the body areas where the Fender Flares will make contact with a clean cloth.

STEP 6: Place the Fender Flare onto the vehicle and fit into the correct position following the contours of the vehicle fender. To secure the Fender Flare to the body take the black metal clips and slide them over the Fender Flare and the inner wheel arch lip. Position the clip so that the barb in the clip locates in the slot of the Fender Flare. Install top center clip first working out to the shown locations.

STEF 7: Raiola (¥E| of I Tram bock god rechain for installation o Freda Flares.

STEP 8: Place the Feder Fare ol e vesicle and B into [ha 2oagl Lok “aliquant the contours of the Ly Ute 2 ol I rainier cllpe ae * dam- bolls o U s E IR Farida Flanna b iha body, Make sum hoe dip i By angers he Fender Flare, MOTE: IF pan fills R . 8t inw0ie Mammalian By aiding <1 Graw rtla bettors fghtaaing lb.

STEP 9: Reynalda] that raralnirg Tamm beaks, b i the 1ronE Norkem Comer and two o the rear ballon carnie.

STEP 10: Ripest -retaliation med had far other side. oyt check he front Fencer Flares o naf soral Atz arc Howl Anca dips anew s=curely fastened. Tour RHAFIANN 15 R Campbell. D nay e surimi rename,

STEP 11: Cyan ice badly amass were ice Feder Flares will ke c00la vt & clean cloth, Fui models supped with Factory [ender e, removal af factory laes 3 enquire., lass consul the ashik ear vice nahual for fakery fade- Fae removal.

STEP : 12 kampung that g Tram factory wheel wel gl tulle JA] =7d the lwa rear Balcony retainer Chas (), retain far msiallaticn of Feder Flares. Remailer < ips (B wil 1w 1 be repaved using needled noise pl errs.

STEP 13: Faiza thin fender Flam anta e vies and Minta Lhe contact postilion [D”D\’Jhg e contoured of U ey, Using T.0imen heeds neonatal e previously remover Telcon gl adores @ lye unipara sed bower [4] sore Iotations trough the shals in the Tent aft take Fender Flare =t the bz nosed lavations. Re-install the factory retainer zaps (3] wrought the hales in the fender flare a1 the twn noted vacations.

STEF 14 : use £ of the U-sky’s e Ferrer Flare o U Leidy. Masa aura The ik in wicLinmly clip wicLinmly allscriis in e ski o e Faience Flare, Repass method [o- holler side. Duduk check ha foal Fender Flares 10 make sire all bakes anew gl and sofas are securely fastens. ¥odor i i conks. D real i abrasive censed,

For Technical Support warranty Information plisse call BE-757-TOTS EGR Inc., 4000 Est Graystone Drive, Ontario, CA 81781

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals