EGR INC FF1002 Bolt Style Look Fender Flares Instruction Manual

June 13, 2024
EGR INC

Installation Instructions
Bolt-Style Look Fender Flares
GMC Canyon (15-On) FF1002

INC FF1002 Bolt Style Look Fender Flares

EGR INC FF1002 Bolt Style Look Fender Flares
Important: Please read instructions entirely before installing this product.

Hardware Included QTY
 Extrusion 29.5ft.
 U CLIP .6mm 10
 Alcohol Towelette 4
 Retaining clips 6
Bolt Kit Included (Bolt-On look flare only) QTY
--- ---
 Extruded Plastic Bolts 42

Ensure that both left and right hand Fender Flares suit the profile of the vehicle. Please take note of the areas where the Fender Flares come in contact with the vehicle.
*PRIOR TO ANY INSTALLATION, PRODUCT SHOULD BE THOROUGHLY INSPECTED FOR ALL COMPONENTS LISTED IN THE TABLES ABOVE. PRODUCT SHOULD ALSO BE TEST FITTED PRIOR TO ANY INSTALLATION. PLEASE CONTACT EGR INC. (1800-757-7075) IF YOU HAVE ANY FITMENT QUESTIONS AND OR MISSING COMPONENTS.
EGR INC FF1002 Bolt Style Look Fender Flares - step 1 STEP 1 : Attach the extruded plastic bolts. Peel back white tape liner from the bottom side of the extruded plastic bolt and press until it snaps into place. Ensure inside of Fender Flares where the rubber seal is attached is clean, using the alcohol wipes provided. Wipe away any residue with a dry clean cloth.EGR INC FF1002 Bolt Style Look Fender Flares - step
2 STEP 2 : Attach the included rubber seal to the Fender Flares. Peel back 2” of the adhesive backing and position on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Ensure pressure is used to secure rubber seal to Fender Flare edge. Attach rubber seal along the top leading edge of the Fender Flare where it will make contact with the vehicle body.EGR INC FF1002 Bolt Style Look
Fender Flares - step 3 STEP 3: Trim rubber seal at end of each Fender Flare. Save extra rubber seal for install on opposite side Fender Flare and discard any excess once both sides are complete.
IMPORTANT NOTE: Trim rubber seal.EGR INC FF1002 Bolt Style Look Fender
Flares - step 4 STEP 4 : Clean the body areas where the Fender Flares will make contact. Ensure fenders are dry prior to install. Turning tires outward during install of each Fender Flare will ensure ease of install at bottom fixing points.EGR INC FF1002 Bolt Style
Look Fender Flares - step 5 STEP 5: Place Fender Flare on the vehicle into the position of best fit. Note where (3) slots in Fender Flare correspond with (3) existing screws in the vehicle wheel arch molding. Remove Fender Flare. Remove the existing vehicle screws in location as shown #15 Torx head screwdriver. Maintain screws for re-install. EGR INC FF1002 Bolt Style Look Fender Flares - step 6STEP 6: Using a #15 Torx head screwdriver remove bottom rear wheel arch molding screw. Maintain screws for re-install. EGR INC FF1002
Bolt Style Look Fender Flares - step 7

STEP 7: Place the Fender Flare onto the vehicle and fit into the correct position following the contours of the body. Use 3 of the retaining clips and previously removed factory screws to secure the Fender Flare to the body using

15 Torx head screwdriver. Make sure the clip securely engages the slots in

Fender Flare.
NOTE: If part fits loosely, add more tension by sliding clip upwards before tightening bolt.EGR INC FF1002 Bolt Style Look Fender Flares - step
8

STEP 8: Install the provided U shape metal clip at the (1) remaining slot location in the Fender Flare. Ensure that positive pressure is applied on the Fender Flare to the vehicle fender when installing clips. Slide the clip over the Fender Flare and the inner lip of the wheel arch molding ensuring that the barb in the clip locates in the slot of the Fender Flare.EGR INC FF1002 Bolt
Style Look Fender Flares - step 9 STEP 9: Loosely re-install previously removed factory screw through the slot in the Fender Flare at the bottom rear wheel arch using #15 Torx head screwdriver. Ensure Fender Flare is centered and in position of best fit on fender. Tighten all front fender fixing points to ensure a tight and secure fit. Ensure that the rubber seal is flush neatly against the vehicle body.EGR INC FF1002 Bolt Style Look Fender Flares - step
10 STEP 10: Clean the body area where the Fender Flareswill make contact. Ensure fenders are dry prior to install.EGR
INC FF1002 Bolt Style Look Fender Flares - step 11 STEP 11 : Using #15 Torx head screwdriver, remove lower screw from the rear factory deflector. Remove the top factory screw from the front rear deflector. Maintain screws for re-install.          EGR INC FF1002 Bolt
Style Look Fender Flares - step 12 STEP 12 : Place Fender Flare on the vehicle into the position of best fit, slide the bottom front end of Fender Flare between the existing mud flap deflector and wheel arch molding so that the slot in the Fender Flare is under the vacant hole in the mud flap. Using #15 Torx head screwdriver, loosely re-install the previously removed screw from front factory deflector.EGR INC FF1002 Bolt Style Look Fender Flares - step
13 STEP 13 : Install the provided U shape metal clips at the (4) remaining slot locations in the Fender Flare. Ensure that positive pressure is applied on the Fender Flare to the vehicle fender when installing clips. Slide the clips over the Fender Flare and the inner lip of the wheel arch molding ensuring that the barb in the clip locates in the slot of the Fender Flare.EGR INC FF1002 Bolt Style Look Fender Flares - step
14 STEP 14 : Using #15 Torx head screwdriver, re-install the previously removed srcew through the bottom rear slot in Fender Flare and factory deflector. Ensure all fixing points are tight and secure and that the rubber seal is flush neatly against the vehicle body and factory deflector.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals