EGR FF1005 Dodge Ram HD Pickup 10 18 Front Fender Flares Instruction Manual

June 13, 2024
EGR

EGR FF1005 Dodge Ram HD Pickup 10 18 Front Fender Flares Instruction Manual
Front Fender Flares

DODGE RAM HD PICKUP (10-18) FRONT FENDER FLARES BOLT-ON INSTALLATION

INSTRUCTIONS

  1. Ensure that both left and right hand Fender Flares suit the profile of the vehicle. Note the areas where the Fender Flares come in contact with the vehicle NOTE: Before fitting Fender Flares remove any mouldings, strips or existing flares from the wheel arch. If there is a body side moulding, mark where the moulding is to be cut, alternatively the Fender Flares can be cut to go around the moulding Be sure to allow enough room for the extrusion
    Installation Instruction
    PAINTING INSTRUCTIONS – If Fender Flares are being painted, do not install edge extrusion until painting is complete. Prior to painting, clean all surfaces to be painted using clean water and a mild detergent, do nol use lacquer thinner or any solvent based products. Wipe completely dry. Best results will be achieved by wiping the areas to be painted with a tack rag just| prior to panting Most automotive paints can be apglied directly to the Fender Flares, however some may require a primer {check paint manufacturer specifications). Good adhesion will be achieved without sanding. Select a paint (and primer if necessary) that| Is suitable for ngid plastics PMMA (Acrylic). If using a paint system which requires baking, do not expose the product to temperatures | ‘above 70°C (158°F). Do not fit the extrusion or any of the hardware to the Fender Flares until the paint is completely dry.
    IMPORTANT : For rugged and OEM Fender Flares to Step 3.

  2. Attach 9 extruded plastic bolts. Begin by peeling back the white tape liner from the bottom side of the extruded plastic bolt and press until it snaps into place.
    Installation Instruction

  3. ‘Wash the areas of contact on the vehicle and wipe dry both the vehicle and the Fender Flares with a clean cloth. Ensure inside of Fender Flares where extrusion is attached is clean, using the alcohol wipes provided and wipe away any residue with a dry, clean cloth.
    Installation Instruction

  4. Remove approximately 2* (50mm) of the protective liner from the extrus.on. Fit the extrusion to the Fender Flare along the edge that comes in contact with the vehicle’s body panel
    Installation Instruction

  5. Pulling at right angles to the extrusion, remove the liner from the extrusion in small portions and apply thumb pressure to ensure that it adheres to the Fender Flares.
    Installation Instruction

  6. Cut notches in extrusion tape to allow it to fit neatly around headlamp area of flare as shown.
    Installation Instruction

  7. Trim any unnecessary extrusion and discard
    Installation Instruction

  8. Note the correct hardware for positions A, B, C, & D (Right Fender Flare shown).
    Installation Instruction

  9. Place the Fender Flare on the vehicle into the position of best fit. Note where the slots in Fender Flare at positions A,B,C and D align with the existing screws in the vehicle. Remove Fender Flare.
    Installation Instruction

  10. Remove the previously noted existing screws and retain for re-installation

  11. Replace the Fender Flare on the vehicle into position of best fil. Complete installation by replacing the previously removed screws at position A, B, C and D, ensuring the Fender Flare is located firmly and extrusion is neat against the vehicle fender. Repeat process for the other side of the vehicle.
    Installation Instruction

CLEAN FLARES WITH MILD DETERGENT ONLY, NO ABRASIVE CLEANERS.

DODGE RAM HD PICKUP (10-18) REAR FENDER FLARES BOLT-ON LOOK INSTALLATION

INSTRUCTIONS

  1. Ensure that both left and right hand Fender Flares suit the profile of the vehicle. Note the areas where the Fender Flares come\ in contact with the vehicle. NOTE: Before fitting Fender Flares remove any mouldings, strips or existing flares from the whee! arch. If there is a body side moulding, mark where the moulding is to be cut, altematively the Fender Flares can be cut to go around the moulding. Be sure to allow enough room for the extrusion.
    Installation Instruction
    PAINTING INSTRUCTIONS – If Fender Flares are being painted, do not install edge extrusion until painting is complete. Prior to painting, clean all surfaces to be painted using clean water and a mild detergent, do not use lacquer thinner or any solvent based products. Wipe completely dry. Best results will be achieved by wiping the areas to be painted with a tack rag just prior to painting. Most automotive paints can be applied directly to the Fender Flares, however some may require a primer (check paint manufacturer specifications). Good adhesion will be achieved without sanding. Select a paint (and primer if necessary) that is suitable for rigid plastics PMMA (Acrylic). If using a paint system which requires baking, do not expose the product to temperatures above 70°C (158°F). Do not fit the extrusion or any of the hardware to the Fender Flares until the paint is completely dry
    IMPORTANT : For boll-on Fender Flares proceed to Step 2. For rugged Fender Flares to Step 3

  2. Attach 11 extruded plastic belts. Begin by peeling  back the tape liner from the bottom side of the extruded plastic bolt and press until it snaps into place
    Installation Instruction

  3. Wash the areas of contact on the vehicle and wipe dry both the vehicle and the Fender Flares with a clean cloth. Ensure inside of Fender Fiares where extrusion is attached is clean, using the alcohol wipes provided and wipe away any residue with a dry, clean cloth
    Installation Instruction

  4. Remove approximately 2″ (50mm) of the protective liner from the extrusion. Fit the extrusion to the Fender Flare along the edge that comes in contact with the vehicle’s body panel.
    Installation Instruction

  5. Pulling at right angles to the extrusion, remove the liner from the extrusion in small portions and apply thumb pressure to ensure that it adheres to the Fender Flares.
    Installation Instruction

  6. Trim any unnecessary extrusion and discard
    Installation Instruction

  7. Note the correct hardware for positions A, B, C, D, E & F (Right Fender Flare shown).
    Installation Instruction

  8. Place the Fender Flare on the vehicle into the position of best fit. Note where the slots in Fender Flare at positions A,D,E and F align with the existing screws in the vehicle. Remove Fender Flare.
    Installation Instruction

  9. Remove the previously noted existing screws and retain for re-installation
    Installation Instruction

  10. Replace Fender Flare on the vehicle into position of best fit. Take the supplied snap clips and fix them into positions B and C, as shown, ensuring the notch in clip locates securely into the slot in the Fender Flare
    Installation Instruction

  11. Complete installation by replacing the previously removed screws at position A, D, E and F,  ensuring the Fender Flare is located firmly and extrusion is neat against the vehicle fender. Repeat process for other side of the vehicle.
    Installation Instruction

CLEAN FLARES WITH MILD DETERGENT ONLY, NO ABRASIVE CLEANERS.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals