RIGID 11-14313-A Tundra Bumper Light Bar Instruction Manual
- June 13, 2024
- RIGID
Table of Contents
INSTALLATION INSTRUCTIONS
2022+ TOYOTA TUNDRA BUMPER LIGHT BAR
PRODUCT INCLUDES:
(2) Lightbar Brackets
PRODUCT FITMENT:
Fits any 20” SR light bar
RECOMMENDED TOOLS:
- Small Flathead Screwdriver or Clip Puller
- 10mm, 14mm, 17mm Socket or Ratchet
- Flush Cut Pliers
- Wire Loom
- Electrical Tape
- Zip Ties
- Tools Required by Light Bar
Manufacture for Installation
THANK YOU FOR PURCHASING RIGID INDUSTRIES’ PRODUCTS FOR YOUR VEHICLE.
Please read through all of these Instructions and tips before proceeding with
the installation.
We do our best to provide a simple installation process for all applications,
however a professional installation is always recommended.
IMPORTANT
Always disconnect any power sources connected to your vehicle before servicing
fuses or electrical systems.
DO NOT just try and pull the front panels from the grill, there are wires that
need to be move around and there is not access to them without pulling the
front clip.
STEP: 1
Tape headlight corners this will prevent scratching the headlights upon
disassembly and installation of the front clip.
STEP: 2
Remove 6 inner fender screws per side all the way up to the one above the
centerline of the front wheel. Place the screws in a safe place or bag for
reinstallation.
STEP: 3
Unplug the four plugs near the top of the grill.
STEP: 4
Pull the wheel well fenders back about ½ way to allow the front clip panels
to be removed.
STEP: 5
Pull the outer wings of the front clip back so they are released from the
body.
STEP: 6
Pull the plastic pull pin clip from each side that is located under the 4
plugs that were disconnected and place is a safe spot for reinstallation.
STEP: 7
Remove the four bolts at the bottom of the front clip out and place in a
safe spot for reinstallation.
STEP: 8
Remove the four bolts at the top of the front clip, these can be place in the
hole in the core support to make it easy to secure the front clip upon re-
installation.
STEP: 9
Setup a blanket or soft place to place the front clip grill down in a good
spot to work on the wiring on the backside. With the bolt removed and wires
unplugged the front clip can now come off the vehicle, having some assistance
will be beneficial to make sure the front clip is pulled evenly.
STEP: 10
With the grill on the ground the wires and temperature sensor will need to
be moved around in order to make room for the light bar. Using a clip puller,
the temperature sensor will need to be pulled by the plastic clip from the
grill and moved down into the wiring loom holder. The wires for the collision
sensor will also need to be undone from the loom and re-loomed and taped
around the light hole opening on the passenger side around the sensor. TRD Pro
ONLY: The camera wiring will also need to be removed from the loom and re-
loomed but run around the driver’s side of the opening for the light bar
(Displayed with red circle).
Before: (TRD Pro Grill Displayed)| After: (TRD Pro Grill with Camera Wiring on
Driver’s Side)
---|---
| 
STEP: 11
Loom and tape over the wires that have been re-routed to make the wires
have a factory appearance and protection.
STEP: 12
Remove the innermost bumper bolts to install the 20” light bar brackets.
STEP: 13
Loosely install the light bar brackets onto the front bumper mounts. DO NOT
tighten these bolts until the light bar is installed and centered.
STEP: 14
Install the light bar to the brackets loosely, each company will have a
different mounting method, see the manufacturer’s instructions. Make sure
light bar wire is above the mounts before ully installing.
STEP: 15
Center the light bar left to right on the front of the vehicle and push the
light bar as far back in the slots as possible. Once the light bar is located
tighten all the bolts on the bumper and the light bar to manufactures
specifications.
STEP: 16
Run the wire from the light bar following the manufacturer’s instructions for
the wiring kit if included. The battery for TRD Pro and Hybrid vehicles have
the battery under the driver’s rear seat.
STEP: 17
Optionally on the lower grill trim the vertical and horizonal plastic bars
with a set of flush cut pliers and file the excess if there is any before
installing the grill. Designated by the red box in the photo. Check the light
to make sure it works properly before installing the front clip.
STEP: 18
Spread the long plastic tabs in the middle of the front clip around the
hole where the light bar is installed. This will keep the tabs from accidently
getting folded in front of the light bar. With the help of an additional
person install the front clip onto the vehicle, use a couple of the bolts at
the top to loosely hold it in place.
STEP: 19
Snap the wings of the front clip back into place and snap the wheel well
fenders back into place
STEP: 20
Check the alignment of the light bar to make sure it is centered in the
hole. Adjust the front clip as necessary.
STEP: 21
Install the 4 bolts at the bottom of the front clip. Center and tighten.
Install the 2 pull pin clips back into the top of the front clip. Plug the 4
plugs back into the front clip. Install the remaining top bolts back into the
front clip. Center and tighten.
STEP: 22
Install the 6 bolts per side into the wheel well, DO NOT over tighten.
STEP: 23
Remove the tape from the headlights. Give everything a once over and enjoy
the new light bar.
Your installation is now complete.
Welcome to the Rigid Nation!
WARRANTY INFORMATION
For warranty information, visit
www.rigidindustries.com/about/warranty
779 N Colorado St, Gilbert, AZ 85233 •
855-760-5337
www.rigidindustries.com
RIGID, SR-M Series, and Rigid Industries are registered and/or common law
marks owned by JST
Performance, LLC, a Delaware limited liability company d/b/a Rigid Industries.
11-14313-A
NOTES:
Documents / Resources
|
RIGID 11-14313-A Tundra Bumper Light
Bar
[pdf] Instruction Manual
11-14313-A, 2022, 11-14313-A Tundra Bumper Light Bar, Tundra Bumper Light Bar,
Bumper Light Bar, Light Bar, Bar
---|---