SHOCKFLO CS02 48A EV Charging Station User Guide

CS02 48AEV
Charging Station
Installation and user guide Please read all instructions carefully before use.

Main part

(1)Master Device:

1. Key Card swipe location
2. LED Strip
3. Charging Connector
4. NEMA14-50 Plug
5. Charging Connector Holder

(2)Accessories:

• Installation and user guide*1
• Key Card*1
• APP User Guide*1
• Wall Bracket*1
• Expansion Screw*4
• Common Screw*1

Product Specifications

SHOCKFLO CS02 EV Charging Station (48A)

Output Cable: 17 ft (5.2m)
Working temperature| -22°F to +122°F
Supported features| Regulates current and power
Schedule a charging start and end time
Start charging| 1. Plug to play
2. Activate by swiping
3. Startimmediately through the APP
4. Seta scheduled charging through the APP
Stop charging| 1. Automatic stop when fully charged
2. Stop by swiping
3. Immediately stop via APP
4. Schedule a time stop through the APP
APP connection method support| WIFI (2.4Ghz)
Bluetooth (5.1)
Charging protection:| Current-leakage Protection
Over-heat Protection
Lightning Protection
Over-current Protection
Under-current protection
Over-voltage Protection
Under-voltage protection
Automatic Power-off
Poor grounding detection
Emergency stop switch
Temperature chip fault detection
Measurement chip fault detection
Relay detection

Product Installation Instructions

(1)Install Prerequisites

(2)Product Installation Steps

1. Attach the wall bracket to the wall, and mark 4fixing points with a pencil; itis recommended to install within 1.3-1.6 meters from the ground.
2. Use an electric drill to drill holes equivalent to the diameter of the expansion screws at the 4 marked fixed points. (Expansion screw specification: M10*80).
3. Fix the wall bracket on the wall, and plug the expansion screws into the 4 drilled fixing holes.
4. Tighten the nut with a wrench, so that the tail of the expansion screw is forced to open, and the wall bracket is fixed.
5. After the charging device is hung on the wall  bracket and fixed, lock the device and the bracket with screws from the bottom.
6. Plugitinto a NEMA14-50R socket and you’re ready to go.

Charging Steps

1. NEMA14-50 plug is connected to the power supply;

2. The charging connector is connected to the charging port of the electric vehicle;

3. Charging starts, and the green light flashes; the way to start charging:
   – plug and play
   – swipe card to start charging
   – APP control to start charging
   – APP scheduled time to start charging);

4. When the charging is completed, unplug the plug from the car; the way to end the charging:
   – stop charging when fully charged
   – stop charging by swiping card
   – stop charging by APP control
   – stop charging at APP scheduled time

Light status during use

inserted into the car, and the APP is not connected to WiFi or Bluetooth;
Blinking Blu| The charging station is powered on, connected to the charging port of the car, and the APP is not connected to WiFi or Bluetooth;
Solid Cyan| The charging station is powered on, the charging connector is not inserted into the car, and the APP is connected to Wifi or Bluetooth
Blinking Cyan| The charging station is powered on, connected to the charging port of the car, and the APP is connected to Wifi or Bluetooth
Solid Green| Charging is complete, the car terminal actively disconnects
Blinking Green| Charging is in progress
Blinking Yellow| The OTA upgrade is in progress. (The progress can be views on SHOCKFLO APP)
Malfunction light status| Status indication  explanation| Troubleshooting| Recovery Scenarios After Troubleshooting
---|---|---|---
Red light flashes 2 times| Leakage| Contact Customer Service| After eliminating the problem, you need to
unplug the plug and reconnect the power
supply, and the device will be back to normal
after restarting
Red light flashes 2 times| Abnormal vehicle interaction| Contact Customer
Service| After troubleshooting,
restore by itself
Red light flashes 3 times| Over voltage| Check power outlet voltage, contact local power center or electrician to check| After troubleshooting, restore by itself
Red light flashes 4 times| Under voltage| Check power outlet voltage, contact local power center or electrician to check| After troubleshooting, restore by itself
Red light flashes 5 times| Over current| Contact Customer Service| After eliminating the problem, you need to unplug the plug and reconnect the power supply, and the device will return to normal after restarting
Red light flashes 6 times| Poor grounding| Check if the power outlet is grounded, contact your local power center/electrician to check| After troubleshooting,
Red light flashes 7 times| Emergency stop| Confirm the status of the emergency stop switch; release the emergency stop manually| After troubleshooting, restore by itself
Red light flashes 8 times| Short circuit| Contact Customer Service| After eliminating the problem, you need to unplug the plug and reconnect the power supply, and the device will return to normal after restarting
Red light flashes 9 times| Over heating| Contact Customer Service| After troubleshooting, restore by itself
Red light flashes 10 times| Temperature chip failure (missing or abnormal data measuring chip temperature)| Contact Customer Service|
Red light flashes 11 times| Metering chip failure (missing or abnormal current and
electricity data)| Contact Customer Service|
Red light flashes 12 times| Leakage protection function self-test is abnormal| Contact Customer Service|
Red light flashes 13 times| Relay sticking| Contact Customer Service|

Caution

1. This is for EV chargers with Type 1 inlet (SAE J1772), suitable for EVs with SAE J1772 charging ports.
2. The device has a precise internal structure. If you have any questions, please contact our customer service at first time. Please don’t take it apart without any professional technical support.
3. Do not soak the top of the charger connector in water.
4. This product is only used for electric vehicle charging. Please do not use it for any other occasions including hauling, bundling, etc.
5. Do not use the charger if the control box is damaged or an abnormal alarm occurs
6. The equipment must be grounded.
7. It isnotrecommended to use this device with extension cords oradapters.
8. Be aware of the risk of electric shock or burns.
9. The device does not contain any user-serviceable parts.
10. Do not disconnect the plug when the electric car charger is working.
11. When you encounter problems with the use or failure of the charging station, please provide the Bluetooth name or product number of the product so that we can quickly help you solve the problem.
12. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Statement:

1. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

BRAND URL: Explore More About SHOCKFLOhttps://www.shockflo.com
SERVICE CENTER: APP Download and Quick User Guide Q&A etc. https://www.shockflo.com/ev-station-sevice.html
CERTIFICATION:

MANUFACTURER: ShenZhen Suncent Auto Parts Technology Company Limited
ADDRESS: 5A1, Building C, Qingchuang City Zhangkeng Community, Minzhi Steet, Longhua District,
Shenzhen, Guangdong, China
BRAND OFFICIAL WEBSITE: www.shockflo.com
TEL: +1 833 499.0559 Mon-Fri 9am-5prn(EST)
EMAIL: support@shackflo.com
SERVICE CENTER URL:
www.shockflo.com/ev-station-service.html.
IF YOU HAVE ANY QUESTION, PLEASE CONTACT US.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>