SupaWarm SOFR9D 2000 Watt Oil Filled Radiator Instruction Manual

2000 Watt
Oil Filled Radiator
with Thermostatic Control
This manual is to be used with the following SupaWarm radiator: SOFR9D
IMPORTANT: Read these instructions before use. Please retain for future reference.

SOFR11D 2500 Watt Oil Filled Radiator

This manual is to be used with the following SupaWarm radiator: soFR11D
IMPORTANT: Read these instructions before use. Please retain for future reference. INCLUDES 24 HOUR TIMER

This product is only suitable for well insulated spaces or occasional use.

PARTS IDENTIFICATION

(A) Castor Wheels
(B) Power Cable Storage
(c) 24 Hour Timer Dial
(D) Variable Thermostat Control
(E) 2 On/Off Heat Power Buttons
(F) Carry Handle
(G) Oil Filled Fins

ELECTRICAL SAFETY

RATING

• AC 220-240V ~ 50/60Hz, 2500W.
• Ensure that the voltage indicated on the identification plate corresponds with the mains voltage.

Please read these instructions fully before use.
WARNING! This appliance must be earthed.
DO NOT TURN HEATER UPSIDE-DOWN DURING OPERATION.

DISPOSAL

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service. Disposing of a household appliance separately avoids possible negative consequences for the environment and health, avoiding inappropriate disposal enables the constituent materials to be recovered to obtain significant savings in energy and resources. As a reminder of  the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin.

IMPORTANT SAFETY INSTRUCTION

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THE PRODUCT.
When using an electrical appliance, basic safety precautions should always be observed, as explained in this manual.
WARNING: To reduce the risk of fire, electrical shock, or injury to person or property:

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• The product is for household use only.

• Connect the appliance to single-phase AC supply of the voltage specified on the rating plate.

• WARNING! In order to avoid overheating, do not cover the heater.

• NEVER leave the heater unattended while it is in use. Always turn the product to the OFF position and unplug it from the electrical outlet when not in use.

• The heater must not be located immediately below an electrical socket-outlet.

• Do NoT run cord under carpeting and do not cover cord with rugs, runners or alike. Arrange the power cord away from areas where people walk and where it will not be tripped over.

• Do NoT operate the heater with a damaged cord or plug, or after the heater malfunctions, has been dropped, or damaged in any way.

• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person to avoid a hazard.

• Avoid the use of an extension cord as this may overheat and cause a risk of fire.

• Use the heater in a well-ventilated area. Do not insert or allow objects to enter any ventilation or exhaust opening.
  Do not use on soft surfaces, like a bed, where openings may become blocked.

• Only use the heater on flat, dry surfaces.

• Do NoT use the heater on items of furniture or fitting where the heater could fall off during use or where the heater openings may become blocked.

• Do NoT place this heater near flammable materials, surfaces or substances, as there may be a risk of fire. Keep the above flammable materials, surfaces or substances at least 1mtr from the front of the product and keep them away  from the sides and rear of the heater.

• Do NoT use the heater in any areas where petrol, paint or other flammable liquids are stored e.g. Garages or workshop where there is risk of hot sparks falling onto the heater.

• Do NoT use this heater in the immediate surroundings of a bath, a shower or a swimming pool.

• NEVER locate the heater where it may fall into a bathtub or other water container.

• This heater is hot when in use. To avoid burns and personal injury, do not let bare skin touch hot surfaces. lf provided, use handles when moving the product.

• Be sure that no other appliances are in use on the same electrical socket as your product as an overload can occur.

• This heater is filled with a precise quantity of special oil.

• Repair requiring opening of the oil container is only to be made by a service agent who must be contacted if there is an oil leakage.

• Regulations concerning the disposal of oil when scrapping the appliance have to be followed.

• The heater should not be used in a room, of which the floor area is less than 5m 2.

• The cord shouldn t be placed nearby the hot surface of the appliance.

• When scrapping the heater, follow the regulations concerning the disposal of oil.

• Children of less than 3 years should be kept away unless continuously supervised.

• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended operating position and they have been given supervision or instruction concerning  use of the appliance in a safe way and understand the hazards involved.

• Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

• CAUTION! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

PLEASE NOTE: It is normal when the heaters are turned on for the first time or when they are turned on after having not been used for a long period of time the heaters may have noise inside. This will disappear when the heater has been on a short while.

MAINTENANCE

• Always remove the plug from the socket-outlet and allow the radiator to cool down before cleaning the heater.
• Wipe radiator with a soft damp (not wet) cloth.

WARNING:

• Do not immerse the heater in water.

• Do not use any cleaning chemicals such as detergents and abrasives.

• Do not allow the interior to get wet as this could create a hazard.
  DO NOT OPERATE HEATER IF ANY OF THE FINS ARE DENTED, DAMAGED OR BROKEN

• To store away the heater, wind the cable around the bobbin and store the heater in a clean dry place.

• In case of malfunction or doubt, do not try to repair the radiator yourself, it may result in a fire hazard or electric shock.

ASSEMBLING THE HEATER

The heater is packaged with the feet unattached. You must attach them before operating the heater. WARNING! Do not operate without feet attached. Do operate the heater only in upright position (feet on the bottom, controls on the top), any other position could create a hazardous situation. CAUTION! Ensure the power cord is not plugged in before attempting to assemble the heater.
The only assembly required for the oil heaters are attaching the wheels onto the main unit. Follow these procedures:

1. Place the radiator body upside-down on a scratch-free location, make sure it is stable and will not fall.

2. Screw off the wing nuts from the U-shaped bolt provided, attach the U-shaped bolt to the U-facing flange between first and second fins (near the front cover).

3. To attach the castor mounting plate to the radiator body, you should insert the threaded ends of the U bolt in the holes on the castor mounting plate.

4. Screw the wing nuts back to the U bolt and fasten the wing nut properly.
   PLEASE NOTE: Do not over tighten, which may cause the damage of radiator flange.

5. Screw off spherical nut from the castor, align the shaft to the hole of the castor mounting plate, insert in, and screw on the spherical nut.

6. Repeat 2, 3, 4 and 5 on the rear of radiator for mounting of the rear castors.

PLEASE NOTE: The rear castors must be mounted between the end two fins.

USING YOUR HEATER

1. Before using the heater, make sure that it is on a flat and stable surface. Damage may occur if it is placed on an incline or decline. Place the heater on the floor at least 90cm away from the wall and any other flammable objects such  as furniture, curtains or plants. (Make sure the power supply used corresponds to the one on the rating label).
2. With the thermostat control switch and the power setting switches in the OFF position, plug the heater into the main power supply.
3. Rotate the thermostat knob clockwise to MAX position and switch the heater on as follows; Switch to ‘l’ for low heat Switch to ‘II’ for medium heat Switch on both for high heat
4. When your room reaches the desired temperature, now slowly rotate the thermostat knob counter clockwise until the pilot light goes out. The thermostat can now be left at this setting. As soon as the room temperature has dropped  below the set temperature, the unit will switch itself on automatically until the set temperature has been reached again. In this way the room temperature remains constant with the most economical use of electricity.
5. If you want to change the room temperature setting, rotate the thermostat knob clockwise to raise the temperature, or counter clockwise to lower it.
6. This heater includes an overheat protection system that shuts off the heater when parts of the heater are getting excessively hot.
7. To completely shut the heater off, turn all the controls to OFF, and remove the plug from the socket-outlet.

USING YOUR HEATER

1. Select the amount of time that you require by turning the timer clockwise (do not turn anticlockwise).
2. Turn the timer on by switching to
3. When the switch is set to on the timer, choose the time frame you require. There are 96 small pins on the timer, each pin represents a 15 minute interval. Pull the pins outward that correspond to the time that you want the heater to  switch on and push the pins inward at the time that you want the heater to switch off.

CAUTION!
DO NOT use the timer function unattended!
The heater will not operate if timer is set to position and the pins are not activated according to the times required.
If the heater looses its electricity supply, for example if the heater is switched off at the mains socket or in the event of a power failure, the time should be reset after the power returns.
The pilot light will be on when the timer is set to position or the timing function is activated.

STORAGE

• Save the box for off season storage.
• Clean the heater following the cleaning instructions in this manual.
• Remove the wheel base assemblies.
• Place the heater, and wheel assemblies in the original box, and store in a cool and dry place.
• If you choose to store your heater fully assembled be sure to cover it to protect it from dust.

CONFORMITY WITH DIRECTIVES

MUNRO IMPORTERS LTD Declaration of Conformity
in accordance with Government Guidance
We, the importer:
Munro Importers Ltd
First Floor, Unit 1 The Quadrangle The Drift, Nacton Road, Ipswich, Suffolk, IP3 9OR
Declare that the product:
Product code: 329861 SOFR11D
Product description: SupaWarm 2500w 11 Fin Oil Filled Radiator
Is in conformity with the relevant statutory instruments and their amendments:
EMC Directive 2014/30/EU and The Electromagnetic Compatibility Regulations 2016
Low Voltage Directive 2014/35/EU and The Electrical Equipment (Safety) Regulations 2016
Commission Regulation (EU) 2015/1188 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for local space heaters
Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) with its Amendments (EU) 2015/863
And is manufactured in accordance with the following Standard or standardized documents:
EN 55014-1:2017+A11:2020, EN 55014-2:2015, EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019 EN 60335-2-30:2009 + All: 2012, EN 60335 1:2012 +AC:2014+A11:2014 +A13:2017 + A1:2019 + A14:2019 + A2:2019, EN 62233:2008
(EC) No 1275/2008 & (EU) No.801/2013, EN 50564:2011 & IEC 62301: 2011, EN 60675:1995 + Al:1998 + A2:2018 + A11:2019
WC 62321-8: 2017, I.EC 62321-3-1: 2013, IEC 62321-5: 2013, IEC 62321-4: 2013+AMD1: 2017 CSV, IEC 62321-7-2: 2017, IEC 62321-7-1: 2015, IEC 62321-6: 2015, ISO 17075: 2017, 62321-1: 2013, IEC 62321-2: 2013
All documentation is held on file and is available, on request, for review.
Authorized Signatory:

Date: 05.04.2023
Name: Dominic Richardson
Position: Product Coordinator
Year of Manufacture: 2023

PRODUCT FEATURES

Whisper-quiet operation
The heater operates in silence as there are no moving parts.
Built-in overheat protection
The heater has a built-in sensor which will turn the heater off if it over- heats.
Heating fins
All 11 fins will heat up when the unit has been switched on.
Variable heat thermostat
Use the dial to adjust the temperature setting to your desired comfort level. Turn clockwise to increase the heat.
Wheels
The wheels form the base of the heater and allows the unit to be moved freely around the room.

THANK YOU FOR PURCHANSING

For a complete range of fires, radiators and heaters please call or visit Supa Brands for further information:

Website: www.supabrands.co.uk
Part of the extensive Supa Brand Range
Helpline: 01473 237 997 PO
Box 1042, Ipswich, IP1 9XY

Correct disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to  promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased.
They can take this product for environmental safe recycling

TECHNICAL DETAILS

Item
Heat Output
Nominal heat output| I Symbol
Pnom| I Value
0.9360| I Unit
kW| Item
Type of heat input, for electric storage local space heaters only (select one)
Manual heat charge control, with integrated thermostat| I Unit
N/A
---|---|---|---|---|---
Minimum heat output (indicative)| Pmin| 0.0002| kW| Manual heat charge control, with room and/or outdoor temperature feedback| N/A
Maximum continuous heat output
Auxiliary Electricity Consumption At nominal heat output| Pmax, c
elmax| 0.9360
N/A| kW
kW| Electronic heat charge control with room and/or outdoor temperature feedback| N/A
Fan assisted heat output
Type of heat output/room temperature control (select one)
Single stage heat output and no room temperature control| N/A
No
At minimum heat output| elmin| N/A| kW
In standby mode| else| N/A| kW| Two or more manual stages, no room temperature control| No
| | | | With mechanic thermostat room temperature control| Yes
| | | | With electronic room temperature control| No
| | | | Electronic room temperature control plus day timer| No
| | | | Electronic room temperature control plus week timer
Other options (multiple selections possible)
Room temperature control, with presence detection| No
No
| | |
| | |
| | | | Room temperature control, with open window detection| No
| | | | With distance control option| No
| | | | With adaptive start control| No
| | | | With working time limitation| No
| | | | With black bulb sensor| No

For a complete range of fires, radiators and heaters
please call or visit Supa Brands for further information:
www.supabrands.co.uk
01473 237 997

Part of the extensive Supa Brand Range
PO Box 1042, Ipswich, IP1 9XY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>