nordlux Rica Round LED Solar Cell Garden Lamp Black Instruction Manual

nordlux Rica Round LED Solar Cell Garden Lamp Black

INSTALLATION INSTRUCTION

• IP4X: Protected against solid objects with a diameter of 1.0 mm or more.
• Hazardous parts are shielded from contact being made using wires ete
• IPX4: Raindrops falling from any angle will not affect the function/safety of the lamp.
• Disposal of waste equipment by users in private households in the European Union. This symbol indicates that this product including batteries must not be disposed of with your other household waste.
• Batteries, electrical, and electronic equipment contain substances that may cause damage to human health and the environment if not recycled correctly.
• It is your responsibility to hand over to a designated collection point for recycling of waste batteries, and electrical and electronic equipment.
• When handing over for correct recycling you help to prevent these products from straining nature and the environment unnecessarily and protect human health.
• For more information regarding correct disposal, please contact your local city office, your household waste disposal service, or the store where you purchased this product.
• We congratulate you on your new outdoor lamp!

Guarantee

• The Nordlux Outdoor lamps in copper, brass, tombac, and galvanized are guaranteed for up to 15 years.
• This guarantee applies to extensive corrosion in the form of holes in the metal caused by rust.
• The guarantee is subject to the presentation of a receipt.
• There is no guarantee on the components that have been damaged by wear and tear or mistreatment of the lamps.

We congratulate you on your new outdoor lamp Stainless steel

• Remember to take care of your lamp. Just follow the guidelines below.
• The shiny, uniform, and decorative surface of stainless steel makes it very suitable for outdoor use.
• It is an alloy consisting of iron, chrome, and nickel. During bath pickling, a thin, rustproof oxide layer forms on the surface.
• The surface is continually vulnerable to atmospheric conditions and other effects of the close environment.
• This means that the lamp must be regularly maintained if its surface is to remain shiny and untarnished by rust.
• Before setting it up, treat your lamp with acid-free oil, and dry it off with a soft cloth. Repeat this three or four times a year.
• Stainless steel lamps are not recommended for use in aggressive environments such as coastal, agricultural, or industrial areas.

Copper, Brass, and Tombac fixtures

• Our copper, brass, and tombac fixtures are made from respectively solid copper, brass, and tombac. The mechanical machining will leave small scratches on the surface, as well as residues of rinse aid.
• This rapidly disappears in the patina process. After the first rain showers, the copper/brass/tombak surface will appear stained, but the aerated air and moisture will soon make the lamp appear with a dark brownish color.
• Over the years, the material copper will get a beautiful patina-green color, and brass/tombac will get a darker and more uniform color.
• The uniformity of the patina surface, as well as the rate at which the process occurs, is dependent on the environment that affects the fixture.

Hot-galvanized lamps

• The zinc treatment of the steel lamps is executed manually in plants.
• The temperature of the melted zinc is about 460 degrees. When the lamps are dipped in melted zinc a reaction between the metalls occurs, which develops alloys in the surface.
• The lamp and the components of the lamp are manually dipped in the hot zinc. This treatment leaves variations in the coating in the form of partly an uneven surface and partly minor formations of drops.
• Thin »zinc curtains« might also occur on the surface and they show as a thin film that hangs down from the edge of the lamp. This film can easily be removed or brushed off with a soft brush.

Condensation

• Condensation is a natural phenomenon arising under specific atmospheric conditions. Damp heat and cold air meet, which causes condensation of water on the surface.
• When water heats up it leads to rising water vapor, which will be able to affect electric components.
• Condensation is not included by Nordlux warranty unless it is possible to prove that a technical /production error in the lighting causes entry of water.
• In case of condensation please check:
• If the lighting is mounted according to instructions. Washers should seal tightly. Make sure to tension screws and lenses.
• In garden lighting rising damp from the ground may cause condensation in the metal post. This problem can be defeated by filling sealing material into the metal post.

Aluminum fixtures

• Our aluminum light fixtures are made from die-cast and/or extruded aluminum, where the light fixture’s design determines whether both types of materials, or just one of them, are used for different parts of the same light fixture. Aluminum light fixtures in raw aluminum are subsequently coated with a special clear coat, which seals the surface to safeguard against corrosion. Painted aluminum light fixtures are powder-coated and have a uniform and smooth surface. To avoid the light fixture tarnishing, it is recommended to clean and wipe the light fixture after mounting and repeat this process 3-4 times each year.
• This is done with a regular cleaning agent. Black light fixtures which are bleached by strong sunlight can also benefit from treatment with silicone spray as needed, to maintain the black color. Mounting light fixtures in coastal, agricultural, or industrial areas is not recommended, as these aggressive surroundings may cause the light fixture to corrode, which may entail spalling, bubbles in the surface, and a whitish incrustation on the light fixture’s surface.
• Drainage holes must be kept free of impurities if any.
• BEFORE ASSEMBLING THE BOLLARD AGAIN DO REMEMBER TO WIPE OFF ALL PARTS!

INSTRUCTIONS

• Please read these carefully before attempting to install this fitting. It is advisable to keep these instructions in a safe place for future reference.
• If this fitting is installed by a contractor, the contractor should ensure that the customer has a copy of these instructions.

SENSOR SPECIFICATIONS

• Voltage: 5V charge by solar panel
  • Angle of detection: 100degrees
• Lux operation: More than 50lux turn off, less than 50lux turn on
  • Time on: NA
• Manual override: NA
  • Max. detection range: Up to 8 meters approx. depending on weather conditions and mounting height.
• NOTE! The 8m detection range applies when a person is walking across the detection area, not working towards the sensor.
• If a person is walking towards the sensor and 1.5m to the left or right of it, the detection range is typically between 4m and 6m.
• Mounting height: 1.8 to 2 meters approx.
• Ambient operating temp.ranger: -20°to+40°Celsius

OPERATION

Normal Power-up

• Under less than 50lux, When people walk through, and the distance is max 8m, the lamp will turn on. When the lux is more than 50 lux, the lamp will turn off.
• Moreover, when the lamp is turning on, after 45S±5S, nobody walks across, and the lamp will turn off automatically.
• www.nordlux.com

Documents / Resources

| nordlux Rica Round LED Solar Cell Garden Lamp Black [pdf] Instruction Manual
Rica Round LED Solar Cell Garden Lamp Black, Rica Round, LED Solar Cell Garden Lamp Black, Solar Cell Garden Lamp Black, Cell Garden Lamp Black, Garden Lamp Black, Lamp Black
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>