JATRHG EV YLOB103-36 EV Charging Station User Manual

JATRHG EV YLOB103-36 EV Charging Station

SELECT POWER

1. Only connect the power plug to the power supply. Do not connect the charging gun to the car.
   

2. Press and hold the button for 3 seconds, then release it to enter the menu.
   

3. Click the button and select ‘Power’, then press and hold for 2 seconds, release, enter the current selection.
   

4. Click the button to select the required current, press and hold the button for 2 seconds to confirm.
   

The current selection must be made before connecting it to the vehicle. You cannot change the current while it is connected to the vehicle.

EV Charging Cable

TYPE 2 (IEC 62196-2 EU European standard)

Good to know

1. This is a Level 2 EV charging cable only for EVs with 2 inlets. Don’t use it for EVs with other types of inlets.
2. This cable has complicated internal structure. Any questions, please contact our Customer Service Manager at the first time. Please do not take it apart without any professional technical support
3. Don’t use it in the water.
4. This product is only for EV charging. Please don’t use it for any other affair, including hauling, binding and so on.

Cautions

1. Only used for EV charging
2. Do not use the charging box if the device is damaged 3.Do not use this device with an extension cord or adapter
3. Please do not open up any part of the device by yourself. Please do not disconnect while the charging box is working
4. Please follow the user manual to use this device

Professional Specification

Service Life:> 10000 times Insulation Resistance: > 1000M 0
Terminal Temperature rise: <50K Contact Impedance: 0.5m 0
Max Working Temperature: -30°C —+ 50°C Sealing gasket: rubber or silicon rubber
Withstand Voltage: 2000V Inlet cable spec: 32.5mrriz(YLOB103-36) 36mrriz(YLOB103-72)
Shell Material: ABS+PC Alloy Cable diameter: 12(mm) / 0.47(in)
Contact Pin: Copper alloy, silver or nickel plating Vibration Resistance: Meet JDQ 53.3 requirements

About Maintenance

In order to ensure the normal service life of the charger and reduce the risk, maintenance must be performed within the specified time; the maintenance of the equipment needs to be completed by professionals, with use of qualified and safe maintenance tools.

• The product is carefully packed in factory. During transportation, strong impact and bumps should be avoided to prevent damage to the outer packaging of the product.
• The product should be placed at an ambient temperature of -30°C—+50°C with a relative humidity of less than 95%.
  The ambient air should not contain acids, alkalis or other corrosive gases and explosive gases, It also should be away from rain, snow, wind and sand.

1. Connect the power cord.

2. Power selection(For the first use)

3. Plug into the car
   

4. Charging
   
   

Product Instruction

Version firmware: V7.6 Curren: 16A
Charging time: 00:00:00
Temperature of Gun head: 00.0 ℃
Temperature of powerbox: 30℃
Voltage: 237v
Total charging energy: 00.01kwh
Real-time power of charging:0000w
Error message: Over courant/Overheat/Leak current/Overvolt
State: Avail / Charging / Over

Indicator state :

Normal power on :
LED Green flow: Charging
LED Green fixed: Charging complete
LED Blue fixed: Make an appointment

Make an appointment to charge

Enter the appointment charging interface [Time set], tap the button , after selecting the appointment charging time, [0h 2h 4h 6h 8h] press and hold for 3 seconds to confirm, the interface pops up, that is, the setting is complete [success], if the battery is fully charged, the charger will automatically stop charging to prevent overcharging

Security Warning

Failure to follow instructions may result in danger!

• Regularly check whether the portable charger has visible damage, there may be an electric shock hazard when using the damaged product.
• Make sure that all safety facilities are available at all times and test then regularly to ensure safety.
• If a ‘Ground Error’ occurs, it must be assumed that the earth wire carries voltage. Please check the circuit and make sure that there is no high-power available in the whole circuit system.
• Before powering on the device, please confirm that the device is properly grounded to avoid accidents.
• All metal parts should be insulated to prevent short circuit caused by the touch of the tool with the metal frame.
• Do not modify, retrofit, or change any part by yourself under any circumstances.
• To ensure a stable service life and operation of the charging cable, operation environment should be kept clean and with constant temperature and humidity. The charging cable must not be used in the presence of volatile gas or flammable atmosphere.
  Please confirm that the input voltage, frequency, circuit breakers and other conditions of the device have already met the specifications before the device is powered on.

Customer Support

TAMITO SAS
176 avenue Charles de gaulles,
92200 Neuilly-Sur-Seine,
France
service@jatrhg.com
CE No: HX220302011118
For more information and video tutorials about using and installation of the EV charger, please visit our website:
www.jatrhg.com

References

• Accueil - jatrhg.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>