Add On 45-1849 Series Speaker Lights Instruction Manual
- June 13, 2024
- Add On
Table of Contents
Add On 45-1849 Series Speaker Lights
Product Information
The 45-1849 Series Angel Eyes Speaker Lights are accessories that can be mounted on most 4 inch speakers. They come with adhesive tape for easy installation and a gasket (optional) for use with 5 inch speakers. The lights are designed to enhance the appearance of your speakers and can be wired into an accessory unit of your choice.
Product Usage Instructions
- Before installing, read the instructions thoroughly.
- Remove the rear speakers as instructed in the manual.
- Remove the seat as described in the Service Manual.
- Disconnect the negative cable from the battery.
- Remove the screws and the right and left pockets.
- Remove the 13 screws and the inner lid from the trunk lid.
- Remove the bolts and the trunk lid.
- Remove the bolts, screws, and the right and left speaker boxes from the trunk lid.
- Separate the inner and outer speaker boxes.
- Place Angel Eye on the speaker’s outer rim using self-adhesive tape. Cut to size as needed.
- Install the speaker unit with Angel Eye light on the left outer speaker box. For 5-inch speakers, use the provided gasket and assemble accordingly.
- Wire Angel Eye light into an accessory unit of your choice. Connect black wire to the ground and black and white wires to power.
- Repeat steps 10-12 on the right side.
- Install the left inner speaker box on the bike.
- Install the rear trunk lid.
- Reinstall the trunk inner lid in the reverse order of removal.
- Reinstall the right and left pockets in the reverse order of removal.
- Connect the negative cable to the battery.
- Reinstall the seat in the reverse order of removal.
For further assistance or inquiries, contact Addon Accessories at 133 Gold St., Worcester, MA 01608. Phone: 508-791-7552 or 800-821-9861. Fax: 508-793-2919. Email: info@addonaccessories.net. Website: www.addonaccessories.net.
Note : Read instructions thoroughly before installing
Parts List
| No. | Description | Qty |
|---|---|---|
| 1 | Angel Eyes | 2 |
| 2 | Adhesive Tape | 2 |
| 3 | Gasket (optional) | 2 |
Tools Required
- Phillips® Screwdriver
- Torque Wrench
Torque Chart
Be sure to tighten all screws to their specified torque.
| Item | n-m | kgf-m | lbf-ft |
|---|---|---|---|
| 5 mm Screw | 4 | 0.4 | 2.9 |
Note : Angel Eyes will fit on most 4 inch speakers.
INSTALLATION
- Remove the rear speakers as instructed below.
- Remove the seat as described in the Service Manual.
- Disconnect the negative cable from the battery.
- Remove the screws and the right and left pockets.
- Remove the 13 screws and the inner lid from the trunk lid as described in the Service Manual.
- Remove the bolts and the trunk lid as described in the Service Manual.
- Remove the bolts, screws and the right and left speaker boxes from the trunk lid.
- Separate the inner and out speaker boxes.
- Place Angel Eye on speaker’s outer rim using self-adhesive tape. Cut to size as needed.
- Install the speaker unit with Angel Eye light on the left outer speaker box.
- a. For 5-inch speakers, use the gasket provided and assemble as shown.
- Wire Angel Eye light into an accessory unit of your choice. Black to the ground and black and white to the power.
- Repeat on the right side.
- Install the left inner speaker box on the bike.
- Install the rear trunk lid.
- Reinstall the trunk inner lid in the reverse order of removal.
- Reinstall the right and left pockets in the reverse order of removal.
- Connect the negative cable to the battery.
- Reinstall the seat in the reverse order of removal.
133 Gold St., Worcester, MA 01608 Ph: 508-791-7552 800-821-9861 fx:508-793-2919 info@addonaccessories.net www.addonaccessories.net