fontastic ANC Plus Digital ENC True Wireless Headset User Manual
- June 13, 2024
- fontastic
Table of Contents
fontastic ANC Plus Digital ENC True Wireless Headset
Thank you for purchasing this Fontastic® TWS Headset „Cero“ with active noise cancellation. Please read the user manual carefully and follow the safety instructions.
Package contents
- 2 x Cero wireless headset
- Storage and charging case
- USB Type-C® charging cable
- 3 pairs of ear tips
- User manual
Overview
- Multifunction sensor
- LED/microphone
- Speaker
- Silicone earpiece
- Headset charging contacts
- Microphone
- LED charging case
- USB-C fast charging port
Getting Started
Charging the headsets
Insert the headsets into the charging case slots. Close the charging case. By
closing the charging case, the headsets get contact and are automatically
charged in the case.
Charging the case
Connect the charging cable that came with the case to the Type-C® charging
input of the case and a travel charger or USB port of a computer to charge the
built-in battery. The charging status indicator flashes red during charging,
changes to white when fully charged, and goes out after a few seconds.
Switching On/Off
Automatic:
Take both headset units out of the charging case, they turn on automatically.
Put the headsets into the charging case and close it, the headsets turn off
automatically.
Manual
Tap and hold the multifunction sensor for 3 seconds, the headset will turn on.
Tap and hold the multifunction sensor for 6 seconds, the headset will turn
off.
Note: The headset units can also be used individually.
Note: Both headsets turn on and off automatically when removed from the case or inserted.
Pairing
The Cero headset must be paired with a Bluetooth® enabled device to be used.
- By removing both headset units from the charging case, they will automatically turn on, sync with each other, and enter pairing mode to connect to a Bluetooth® source.
- Search for „Cero“ on your Bluetooth® enabled device and select it from the list of found devices to pair the headset with the Bluetooth device.
Note: When the headset is placed in the charging case, the connection is interrupted. As soon as both headsets are removed, they will automatically reconnect. If the headset units do not connect auto-matically or an existing connection is disconnected, switch both headsets off and on again either by inserting and removing them from the charging case, or manually.
Note: If the headset does not find a Bluetooth®-ena-bled device, it switches off after approx. 2 minutes.
Fitting the headset
If necessary, replace the fitted earpieces with ones that are the right size
for you. Choosing the right earpieces will give you better sound quality and
noise cancellation. Carefully insert the headsets into the ears and adjust the
headsets so that they fit comfortably in the ear.
Music Control
All control commands are executed with the multifunction sensor.
Play/Pause: Double-tap the multifunction sensor on either headset.
Skip Backwards: Tap the multifunction sensor of the left headset 3 times.
Skip Forwards: Tap the multifunction sensor of the right headset 3 times.
Hands-free functions
Answer/hang up/reject call:
Answer incoming call : Tap the multifunction sensor on either headset
unit once.
End ongoing call: Tap the multifunction sensor on either headset 2 times.
Reject incoming call: Press and hold the multifunction sensor on either
of the two headset units for 2 seconds.
Modes
Cero features active ambient noise cancellation (ANC + ENC), so ambient noise is not distracting when streaming music or making phone calls.
Note: When you remove the earphones from the charging cradle, the headphones are in Normal mode.
Switching modes
Press and hold the multifunction sensor on either headset unit for 2 seconds
to switch between ANC mode, Transparent mode and Normal mode. The respective
mode is announced when switching.
Voice assistant
Tap the multifunction sensor on either headset unit four times to activate the
voice assistant.
Adjusting the volume
- Increase volume: Tap the multifunction sensor on the right headset once. Repeat this step until the desired volume is reached.
- Decrease volume: Tap the multifunction sensor on the left headset once. Repeat this step until the desired volume is reached.
- Note: In rare cases, the super bass of the headset may be overdriven by the settings of the mobile phone. In this case, use the „Normalise“ function (also „Adjust volume“) in the audio settings of your phone.
Safety advice
- Do not use the headset at high volume for prolonged periods of time.
- Be careful not to use the headset in potentially dangerous situations.
- Do not use the headset while operating a vehicle.
- Never open the device.
- Never immerse the device in water, always protect it from moisture.
- Disconnect electronic devices from the power when not using them for a longer time.
- Do not use headphones if they show any visible damage.
- Charge the headsets and charging case at least once every 6 months.
- Do not store the product in extreme temperatures (below 0°C or above 45°C).
- Do not use chemicals or detergents to clean the product.
Technical data
Headsets
- BT version 5.3
- Profiles: Headset, Handsfree, A2DP, AVRCP
- Range: up to 10 m
- Driver: 10 mm
- Frequency: 20hz-20Khz
- Impedance: 32Ω ± 15%
- Sensitivity: 108±3dB
- Noise reduction: ANC + digital ENC
- ANC Level: -30dB ±3dB
- Voice announcement: German/English
- Status LED
- Battery: 40 mAh Li-Polymer
- Operating time : up to 7 hours
- Dimension per unit: 33.5 x 17 x 16 mm
- Weight: 4.6g
Charging case
- Battery: 300 mAh Li-Polymer (charges headset 3 times).
- UBS-Type-C® fast charging port
- Dimensions: 53 x 53 x 26.5mm
- Weight: 34g
The company is not responsible for any damage due to improper operation. If you need technical support, please contact our support team by e-mail at service@fontastic.eu.We hereby declare, that this device carries the CE mark in accordance with the regulations and standards. It conforms with the fundamental requirements of the (RED) 2014/53/EU directive. The full text of the EU Declaration of Conformity is available at the following Internet address www.d-parts.de/Konfo
Note on environmental protection
After the implementation of the European Directive 2012/19/EU in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country. This symbol on the product, the instruction manual, or the package indicates that a product is subject to these regulations. By recycling, re-using the materials or other forms of utilizing old devices, you are making an important contribution to protecting our environment.The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks is under license. USB Type-C® and USB-C® are trademarks of USB Implementers Forum. Improvements and changes to the technical specifications and other data could be made without prior notice. Registered trademarks are the property of their respective owners. Fantastic, by D-Parts GmbH Birkenweiher Str. 16
- 63505 Langenselbold, Germany
- www.d-parts.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>