Fontastic 263446 Foldable Wireless Desk Charger User Manual
- June 13, 2024
- fontastic
Table of Contents
Foldable Wireless
Desk Charger Fold
263446 Foldable Wireless Desk Charger
USER MANUAL
Dear Customer, Thank you for purchasing this wireless charger. The inductive
charger is powered by only one power source and can charge 2 devices
simultaneously.
Place your Qi-enabled smartphone, smartwatch and wireless headphones on the
corresponding charging point and it will charge automatically.
This instruction manual is designed to familiarize you with the operation of
this product. Please read this user manual and follow the listed safety
instructions and tips. Keep this manual so that you can access it at any time.
Scope of delivery
- Inductive charger „Fold
- USB Type-C ® cable
- Adapter USB-A, Micro USB, 8-pin
- SIM card pin
- User manual
Overview
- Accessory compartment
- Charging point smartphone/headset
- Charging point smartwatch
- USB Type-C ® port
Accessories
Use the parts located in the accessory compartment to be able to connect devices with different ports.
- Micro USB adapter
- USB-A adapter
- USB Type-C ® cable
- Case cover
- 8-pin adapter
- SIM card needle
Unfold the charger
Unfold the charger by lifting the top part and pulling the parts apart. The
charger can be folded or set up as desired. The parts of the charger are held
together by the internal magnets.
NOTE: Devices can also be charged when folded or set up.
Supplying power to the charger
Connect the included USB cable to the charger‘s USB Type-C ® power port and a
USB charger. After switching on, the LED flashes blue 3 times and then changes
to red. The device switches to standby mode and is ready for charging.
NOTE: To ensure 2 devices can be charged safely and efficiently with the
fast charging function, you must use a USB fast charger (QC3.0 and Power
Delivery) with at least 20 watts of power.
Charging devices Smartphon e:
Place the smartphone in the center of the smartphone charging point area.
The charging process starts. The LED lights up blue during charging and turns
off when the device is fully charged. If the LED flashes blue, there is a
malfunction. Please adjust the smartphone on the charging surface. Remove
objects that are between the charging surface and the smartphone. Make sure
that the smartphone supports inductive charging.
NOTE: Fold is suitable for charging MagSafe compatible smartphones (some
iPhone models). If you want to use the magnet function with a non-MagSafe
compatible smartphone, use appropriate metal rings to stick to smartphones or
their protective cases.
Wireless headphones:
Place the Qi-enabled case of the wireless headphones in the center of the
smartphone charging point. The charging process will start.
Smartwatch:
Place your Qi-enabled smartwatch in the center of the Watch charging point.
The charging process will start.
NOTE: There should be no metallic objects between the charger and the
smartwatch.
Safety instructions:
- Never open the device.
- Do not immerse the device in water and protect it from moisture.
- Place the device only on flat surfaces.
- Never connect the device by force.
- Unplug electronic devices if they are not going to be used for a long period of time.
- Do not place cards with magnetic strips, magnetic recording media or metal objects on the charging surface. Charging does not take place and can lead to overheating!
- If necessary, remove the case before placing your smartphone on the charging base.
- Wearers of pacemakers should keep a sufficient distance between the charger and the pacemaker. Consult the attending physician in case of doubt.
- This product may impair the function of medical devices. Therefore, do not use it in clinics and medical facilities.
- Never use the product if it shows visible damage.
No liability is accepted for damage in the event of incorrect operation!
Troubleshooting:
If charging is interrupted or stalls, check the following:
- There should be no metal parts or credit cards or the like on the back of the devices to be charged.
- Place the devices to be charged in the middle of the inductive charging area.
- Cell phone cases should not be thicker than 5 mm to ensure efficient charging.
- Check if the USB charger is a fast charger.
Specifications:
- Input: 5V/2A 9V/2.23A max. 20W
- Smartphone charging point: 5.0W/7.5W/10.0W /15.0W
- Watch charging point: 2.5W
- Connector: USB Type-C ®
- Adapter: USB Type-C ® to USB-A, Micro USB, 8-pin
- Safety: short-circuit protection, overcharge and discharge protection, foreign object detection, overheat protection
- Material: ABS
- Weight: 102g
- Dimensions: 260 x 65 x 8mm (unfolded)
If you need technical support, please contact our support team by email at [email protected].
Registration and Safety
Certification/General Information
We hereby declare, that this device carries the CE mark in accordance with the
regulations and standards. It conforms with the essential requirements of the
RED directive 2014/53/EU, as well as the RoHS 2 2011/65/EU directive. You can
find the complete declaration of conformity under
www.d-parts.de/Konfo
Note on environmental protection:
After the implementation of the European Directive 2012/19/EC in the national
legal system, the following applies: Electrical and electronic devices may not
be disposed of with domestic waste. Consumers are obliged by law to return
electrical and electronic devices at the end of their service lives to the
public collecting points set up for this purpose or point of sale. Details of
this are defined by the national law of the respective country.
This symbol on the product, the instruction manual or the package indicates
that a product is subject to these regulations. By recycling, re-using the
materials or other forms of utilizing old devices, you are making an
important contribution to protecting our environment.
USB Type-C ® and USB-C ® are trademarks of USB Implementers Forum.
Improvement and changes of the technical specifications and other data’s could
be made without prior notice.
Registered trademarks are the property of their respective owners.
Fontastic, by D-Parts GmbH
Birkenweiher Str. 16 ● 63505 Langenselbold, Germany ●
www.d-parts.de
V1_0823