AMP ADL-2010 Series Console SSL Console Installation Guide

: June 13, 2024
: AMP

Table of Contents

AMP ADL-2010 Series Console SSL Console
INSTALLATION & MAINTENANCE GUIDE
IMPORTANT SAFETY INSTRUCTIONS
PACKAGE CONTENTS
PRODUCT DIMENSIONS
Remove Lens Assembly
WIRE CONNECTION
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AMP ADL-2010 Series Console SSL Console

INSTALLATION & MAINTENANCE GUIDE

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION

This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, and property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation maintenance, or mounting situations.

Make sure the power is turned OFF before installing or servicing this luminaire.
WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from the pool, spa, or fountain.
This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
Wiring connections must be made with wire connectors that are suitable for outdoor use.
Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire, or a fitting.
The main low-voltage cable is intended for shallow burial – less than 6 inches (152 mm).
If additional lengths of low-voltage cable are required, please contact www.amplighting.com or call 1-813-978-3900.

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING A RISK OF FIRE, OR INJURY TO PERSONS Lighted Lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

Turn off/unplug it and allow it to cool before replacing the lamp.
The lamp gets HOT quickly! Contact only switch/plug when turning on.
Do not touch the hot lens, guard, or enclosure.
Keep lamps away from materials that may burn.
Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may damage the lamp.
Do not operate the luminaire fitting with a missing or damaged shield.

PACKAGE CONTENTS

A. (1) Luminaire
B. (1) Lock Screws

PRODUCT DIMENSIONS

AMP-ADL-2010-Series-Console-SSL-Console-fig-1

Pro Technique for Hiding Lead Wire

Determine the location of the fixture.
Drill a hole straight through the desired mounting location and run the lead wire out the backside of the location so that the wires are not visible from the front side.
Use a matching trim piece and cut a groove in the back of the trim.
Cover the lead wires with the matching trim piece.

Pro Technique for Hiding Splice Connections

All fixtures come with 4’ of lead wire enabling you to hide the splice connections out of sight.
If you must make a splice connection in view, use an in-line heat shrink style connection that is less visible than traditional twist caps.

Remove Lens Assembly

Rotate the lens assembly counterclockwise until it stops and then lift the lens assembly straight off.
Note: The first time it may be difficult because the luminaire has a tight o-ring seal and a grease sealant for moisture protection.

AMP-ADL-2010-Series-Console-SSL-Console-fig-2

Install Base

Attach the base to the desired location and secure it with the lock screws.
Note: Wall anchors are required for certain installation conditions (e.g. Brick wall, Concrete Wall, etc.). Mark on the wall for wall anchors from the holes on the base. Remove the base and drill proper holes on the wall and then insert the wall anchors.

AMP-ADL-2010-Series-Console-SSL-Console-fig-3

WIRE CONNECTION

Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.

AMP-ADL-2010-Series-Console-SSL-Console-fig-4

Install Bulb

Insert the bulb with the correct wattage and type marked on the luminaire label.

CAUTION: Do not exceed the maximum wattage marked on the luminaire label.
NOTE: DO NOT touch the bulb with bare hands. Use a soft cloth to handle the bulb.

Install Lens Assembly

Push the lens assembly back onto the base aligned with the gaps on the base. Push hard (moisture-proof fixture requires force to get air out).
Once the lens assembly is flush with the base, rotate the lens assembly until it stops and locks into place.

Install/Replace Bulb

Rotate the lens assembly and then remove it to expose the bulb and replace it with the correct wattage and type marked on the luminaire label. And then reinstall the lens assembly.
IMPORTANT: Halogen bulbs must be protected from moisture and dust at all times. Always reinstall the lens assembly when moved.