INTELLINET IPS-08G-95W 8 Port Gigabit Ethernet PoE Switch Instruction Manual
- June 13, 2024
- INTELLINET
Table of Contents
INTELLINET IPS-08G-95W 8 Port Gigabit Ethernet PoE Switch Instruction
Manual
Important: Read before use.
For additional benefits:
Scan to register your product warranty
or go to: register.intellinet-network.com/r/561624
The Intellinet 8-Port Gigabit Ethernet PoE+ Switch with PoE Passthrough offers an array of time-saving, cost-effective features while providing superior network throughput. No configuration is required and installation is plug and play.
Features
- Supports up to 95 W power input from a PoE injector or switch (port 8)
- Provides up to seven PoE network devices with power and data (ports 1 – 7)
- Doubles the connection distance between PoE source and device from 100 m (328 ft.) to 200 m (656 ft.)
- Powered via PoE, DC power adapter or industrial power supply (not included)
- Two redundant DC inputs (48 – 57 V) with I/O terminal block
With a backplane speed of 16 Gbps, plenty of performance is available for your
computers, servers and other networking devices. Each of the ports
automatically senses the link speed of the connected network device and
adjusts to 10, 100 or 1000 Mbps for compatibility and maximum performance.
This PoE switch is designed to provide compatible devices with enough power
when needed.
It offers up to 30 watts of power per port until its power budget of 120 watts
is reached.
For specifications, visit intellinet-network.com. Register your product at
register.
intellinet-network.com/r/561624 or scan the QR code on the cover.
Front Panel
DIP Switch — VLAN
OFF : default mode; allows normal communication between ports 1 – 8.
ON : isolates ports 1 – 7 from each other but allows them to connect to port
8; increases the forwarding rate when broadcast storms occur.
Power
A) PoE Passthrough
B) Terminal Block Installation
NOTE: Ensure all power is off/disconnected before beginning!
-
Loosen appropriate screws.
-
Insert bare power-supply wires into appropriate terminal slots (positive
wire into positive slot; negative wire into negative slot). -
Tighten appropriate screws to secure wires. (If desired, repeat steps 1 – 3 on second input pair.)
-
Install block into the device and tighten screws.
Placement
Desktop Installation
Prior to use, place/position the switch:
- on a level surface with at least 25 mm (approx. 1”) of clearance for ventilation
- away from sources of electrical noise: radios, transmitters, broadband amplifiers
within 100 m (approx. 328’) of network devices it’s to be connected to.
DIN-Rail Installation
- With DIN-rail bracket attached to device with screws, angle bracket onto DIN rail.
- Push device in till it clicks into place.
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
DISPOSAL OF ELECTRIC AND ELECTRONIC EQUIPMENT
(Applicable In The European Union And Other European Countries With Separate
Collection Systems)
ENGLISH: This symbol on the product or its packaging means that this product
must not be treated as unsorted household waste. In accordance with EU
Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), this
electrical product must be disposed of in accordance with the user’s local
regulations for electrical or electronic waste.
Please dispose of this product by returning it to your local point of sale or
recycling pickup point in your municipality.
WARRANTY AT:
REGULATORY STATEMENTS
Class A
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the Federal Communications Commission
(FCC) Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instruction
manual may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the
interference at his own expense. Any changes or modifications made to this
equipment without the approval of the manuafacturer could result in the
product not meeting the Class A limits, in which case the FCC could void the
user’s authority to operate the equipment.
CE
ENGLISH: This device complies with the requirements of CE 2014/30/EU (UKCA
Electromagnetic Compatibility Regulations 2016) and / or 2014/35/EU (UKCA
Electrical Equipment [Safety] Regulations 2016). The Declaration of Conformity
for is available at:
support.intellinet-network.com/barcode/561624
All trademarks and trade names are the property of their respective owners.
All trademarks and trade names are the property of their respective owners.
© IC Intracom. All rights reserved. Intellinet Network Solutions is a
trademark of IC Intracom, registered in the U.S. and other countries.
Printed on recycled paper.
Read More About This Manual & Download PDF:
References
- Intellinet Network Solutions - Provider of PoE and Data Center Product
- Intellinet Network Solutions - Provider of PoE and Data Center Product
- Intellinet Network Solutions Account and Product Registration
- Intellinet Network Solutions Account and Product Registration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>