GE 23113LO Cedar Rock Fir Pre Lit Artificial Tree User Manual
- October 31, 2023
- GE
Table of Contents
GE 23113LO Cedar Rock Fir Pre Lit Artificial Tree
Assembly Instructions
- Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas tree. Should you have any problems with your tree, visit us at www.geholidaylighting.com for more information. You can call our toll-free number at 1-877-398-7337.
- Check our website for the latest service hours and assembly instruction videos.
TREE ASSEMBLY DIAGRAM
NOTE: No tools required
- This tree is provided with an extension cord for a tree topper, which can be attached to the top section along the pole.
- As an option, the tree adapter can be plugged into the back of the tree top extension cord as an add-on. This feature allows you to utilize only one outlet.
**Tree Sections Tree Stand Approx. Asm Time***
- 7.5 ft tree 3 Metal 5 – 10 minutes
Troubleshooting Tips
If the tree does not illuminate, try stepping on the Color Change Foot Pedal
and make certain the wall switch is turned on. If one section of your tree
does not illuminate, check that section for cut or damaged wires or that all
electrical connections on tree are made. Due to the unique construction of the
light sets, the individual LEDs are not replaceable. The light sets are
designed for continued operation even if an individual LED fails to light.
DISCLAIMER: DO NOT USE OR INSTALL ADDITIONAL CHRISTMAS LIGHTING OR
ORNAMATION THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY RESULT IN
DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL INJURY. DOING THIS WILL RESULT
IN A VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.
Disconnect the decorative item from the power source before performing any
maintenance or cleaning. For indoor use only 120v
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
GE is a trademark of General Electric Company and is under license by Nicolas
Holiday Ltd.
USING INSTRUCTIONS
- Carefully unpack the carton. Remove bubble wrap and inspect the sections of your tree. The carton should include sections labeled “A”, “B” and “Top”, as well as a Tree Stand.
- The tree stand should be open and set at 90″ angle.
- Insert Section labeled A into the tree stand, and tighten the thumbscrew. Then insert the plug into an electrical wall outlet.
- Untie the RED twist-tie to release branch panels. All branches should fall into place with a gentle pull on the outer layer of branches. Fig. A. Start at the inner and stagger the tips. Move each tip up to 40″. Fig. B. Make tips 2 & 3 to horizontal, tip 4 to vertical and tips 5 and 6 up to 45″.
- To assemble the section labeled “B”, properly align and insert section “B” into the top of the section “A”. (See Fig. C) Adjust branch tips, as needed, for a fuller look.
- Repeat “Step 4” for shaping.
- To assemble the tree top, properly align and insert the “TOP” section into the top of section “B”. (See Fig. D) Adjust branch tips, as needed, for a fuller look.
- Gently press on foot pedal to select the desired lighting function. (See below)
Tree Storage
-
Remove the tree’s main extension cord plug from the wall outlet.
-
Starting at the top, disconnect the “TOP” from section “B” and then disconnect section “B” from section “A”. {Fig. 1}
Note: Gently fold the tips in branches and fold the branches up toward the center. {Fig. 2} Care should be taken to avoid damage to the lights. -
Remove section “A” from the tree stand and close the tree stand to place it into the carton.
-
Refer to the drawing on how to repack your tree. {Fig. 3}
IMPORTANT: Store your carton neatly in a cool, dry location protected from sunlight to prolong the tree’s life and to keep the light sets in working order. Do not place a heavy load on the carton to avoid damage to or crushing the carton and tree inside.
Spare parts included|
3-amp
---|---
Qty| 2 pcs
Nicolas Holiday Ltd.
- ©2023 Nicolas Holiday Lid.
- Suite 2706 Skyline Tower, 39 Wang Kwong Road, Kowloon Bay, Kowloon, Hong Kong
- All rights reserved. Printed in China NHL Modal No. 23113LO 23116LO 23141LO
- www.geholidaylighting.com.