GE 23102LO 7.5 ft Fir Pre Lit Christmas Tree Instruction Manual
- June 13, 2024
- GE
Table of Contents
GE 23102LO 7.5 ft Fir Pre Lit Christmas Tree Instruction Manual
Assembly Instructions
Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas tree. Should you have any problems with your tree, visit us at www.geholidaylighting.com for more information. You can call our
toll free number at 1-877-398-7337. Check our website for latest service hours and assembly instruction videos,
TREE ASSEMBLY DIAGRAM
SCHEMATIC DIAGRAM
NOTE: No tools required
| Tree Sections | Tree Stand | Approx. Asm Time* |
|---|---|---|
| 751t tree | 3 | Metal |
-
Carefully unpack the carton. Remove bubble wrap and inspect the sections of your tree.
The carton should include sections labeled “A”, “B” and “Top”, as well as a Tree Stand.
-
The tree stand should be open and set at 90° angle.
Thumbscrew
-
Insert Section labeled A into tree stand, tighten the thumbscrew. Then Insert the plug into an electrical wall outlet.
-
Untie RED twist-tie to release branch panels. All branches should fall into place with a gentle pull on the outer
Fig. A. Start at the inner and stagger the tips. Move each tip up to 40°.
Fig. B. Make tips 2 & 3 to horizontal, tip 4 to vertical and tips 5 and 6 up to 45°.
-
To assemble the section labeled “B”,properly align and insert section “A”. ( See Fig. C ) Adjust branch tips, as needed, for a fuller look.
Fig.C Itis important that you align the mark when you connect two tree sections. -
Repeat “Step 4” for shaping.
-
To assemble the tree top, properly align and insert the “TOP” section into the top of section “B”. (See Fig. D) Adjust branch tips, as needed, for a fuller look
Fig. D It is important that you align the mark when you connect two tree sections. -
Gently press on foot pedal to select the desired lighting function. (See below)
Troubleshooting Tips
Tree Storage Ifthe tree does ot iluminate, try stepping on the Color Change
Foot Pedal and make certain the wall switch is tumed on. If one section of
your tree does.
not illuminate, check that section for cut or damage wires or that all electrical connections on tree are made. Due to unique construction of the light sets, the individual LEDs are not replaceable. The light sets are designed for continued ‘operation even if an individual LED fails to light
DISCLAIMER : DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS LIGHTING ‘OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY RESULT IN DAVAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.
THIS PRODUCT. Disconnect the decorative item from the power source before
performing any maintenance or cleaning. For indoor use only 120V
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY. GE is a trademark of General
Electric Company and is under license by Nicolas Holiday Ltd.
Nicolas Holiday Led.
©2023 Nicolas Hoiiday Lid Suite 2706 Skyline Tower, 39 Wang Kong Road, Kowloon
Bay, Kowloon, Hong Kong Allghis roserved. Printed n China NHL Model No.
23102L0 231360
Tree Storage
-
Remove the tree’s main extension cord plug from the wall outlet.
-
Starting at the top, disconnect the “TOP” from section “B” and then disconnect section “B” from section “A”. {Fig. 1}
Note: Gently fold the tips in branches and fold the branches up toward the center. {Fig. 2} Care should be taken to avoid damage to the lights. -
Remove section “A” from the tree stand and close tree stand to place into the carton.
-
Refer to the drawing on how to repack your tree. {Fig. 3}
IMPORTANT: Store your carton neatly in a cool, dry location protected from sunlight to prolong the tree life and to better keep the light sets in working order. Do not place a heavy load on the carton to avoid damage to o crushing the carton and tree inside