GE 23114LO 7.5 ft Fir Pre lit Artificial Tree Artificial Christmas Tree Instruction Manual

: June 13, 2024
: GE

Table of Contents

Assembly Instructions
Troubleshooting Tips
Nicolas Holiday Ltd
Tree Storage
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GE 23114LO 7.5 ft Fir Pre lit Artificial Tree Artificial Christmas Tree

Assembly Instructions

Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas tree. Should you have any problems with your tree, visit us at www.geholidaylighting.com for more information. You can call our toll free number at 1-877-398-7337.
Check our website for latest service hours and assembly instruction videos.

Assembly Instructions

NOTE:

No tools required

| Tree Sections| Tree Stand| Approx. Asm Time*
---|---|---|---
7.5 ft tree| 3| Metal| 5-10 minutes

Carefully unpack the carton. Remove bubble wrap and inspect the sections of your tree.
The carton should include sections labeled “A”, “B” and “Top”, as well as a Tree Stand.
The tree stand should be open and set at 90° angle.
Insert Section labeled A into tree stand, tighten the thumbscrew. Then insert the plug into an electrical wall outlet.
Untie RED twist-tie to release branch panels. All branches should fall into place with a gentle pull on the outer layer of branches.
Fig. A. Start at the inner and stagger the tips. Move each tip up to 40°. Fig. B. Make tips 2 & 3 to horizontial, tip 4 to vertical and tips 5 and 6 up to 45°.
To assemble the section labeled “B”, properly align and insert section “B” into the top of section “A”. (See Fig. C) Adjust branch tips, as needed, for a fuller look.
Repeat “Step 4” for shaping.
To assemble the tree top, properly align and insert the “TOP” section into the top of section “B”. (See Fig. D) Adjust branch tips, as needed, for a fuller look.

It is important that you align the mark when you connect two tree sections.

Troubleshooting Tips

If the tree does not illuminate, make certain the wall switch is turned on. If one section of your tree does not illuminate, check that section for loose or missing bulbs, all factory connections are properly made or that you properly made all the electrical connections between each tree section, i.e., tree plug to extension cord outlet.

DISCLAIMER: DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.

Disconnect the decorative item from the power source before performing any maintenance or cleaning.

For indoor use only 120v

THIS IS NOT A TOY, FOR DECORATIVE USE ONLY. GE is a trademark of General Electric Company and is under license by Nicolas Holiday Ltd.

Nicolas Holiday Ltd

Tree Storage

Remove the tree’s main extension cord plug from the wall ouflet.
Starting at the top, disconnect the “TOP” from section “B” and then disconnect section “B” from section “A”. {Fig.1}
Note: Gently fold the tips in branches and fold the branches 7 To assemble the tree top, properly align and insert the “TOP” section into the top of section “B”. (SeeFig.D) Adjust branch tips, as needed, for a fuller look. Fig. D It is important that you align the mark when you connect two tree sections. up toward the center. {Fig. 2} Care should be taken to avoid damage to the lights.
Remove section “A” from the tree stand and close tree stand to place into the carton.
Refer to the drawing on how to repack your tree. {Fig. 3}

IMPORTANT: Store your carton neatly in a cool, dry location protected from sunlight to prolong the tree life and to better keep the light sets in working order. Do not place a heavy load on the carton to avoid damage to or crushing the carton and tree inside.