GE 23139LO Laurel Pine Pre lit Artificial Tree Instruction Manual

GE 23139LO Laurel Pine Pre lit Artificial Tree Instruction Manual

Assembly Instructions

Assembly Instructions Nicolas Holiday Ltd. thanks you for purchasing this pre- lit Christmas tree. Should you have any problems with your tree, visit us at www.geholidaylighting.com for more information. You can call our toll free number at 1-877-398-7337. Check our website for latest service hours and assembly instruction videos.

TREE ASSEVMBLY DIAGRAM

Tree Stand

OPEN SCHEMATIC DIAGRAM

NOTE: No tools required

| Tree Sections| Tree Stand| Approx. Asm Time*
---|---|---|---
751t tree| 3| Metal| 10 – 15 minutes

1. Carefully unpack the carton. Remove bubble wrap and inspect the sections of your tree. The carton should include sections **“A”,”B” and “Top”, as well as a Tree Stand.

**

2. The tree stand should be open and set at 90° angle.

3. Insert Section A into tree stand, tighten the thumbscrew. Then sert the plug into an electrical wall outlet.

4. Untie RED twist-tie to release branch panels. All branches should fall into place with a gentle pull on the outer layer of branches. Fig. A.Start at the inner and stagger the tips. Move each tip up to 40°. Fig. B. Make tips 2 & 3 to horizontial, tip 4 to vertical and tips 5 and 6 up to 45°.

5. To assemble the section” properly insert section into the top of section “A”. (See Fig. C) Adjust branch tips, as needed, fora fuller look.

To electrically connect the sections please refer 1o the Tree Assembly Diagram. Take the male and female connectors, locate the flat area on each and fully insert the connectors together. Fully screw on securing cap.

6. Repeat “Step 4” for shaping.

7. section “B”. (See Fig. D) To assemble the tree top, properly insert the “TOP” section into the top of Adjust branch tips, as needed, for a fuller look.

To electrically connect th top, again refer 10 the Tree Assembly Diagram taking the male and female connectors, aigning the flat areas and fully inserting together. Fuly screw on securing cap.

Troubleshooting Tips

If one section of your tree does not lluminate, check that section for cut or damage wires or that all electrical connections on tree are made. Due to unique construction of the light sets, the individual LEDs are not replaceable. The light sets are designed for continued operation even if an individual LED faiils to light.

DISCLAIMER : DONOT USE ORINSTALL ANY ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.

Disconnect the decorative item from the power source before performing any maintenance or cleaning.
For indoor use only 120V
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY. GE s a trademark of General Electric Company and is under license by Nicolas Holiday Ltd.
Nicolas Holiday Led. ©2023 Nicolas Holiday Ld. Sute 2706 Skyline Tower, 39 Wang Kwong Road, Kowloon Bay, Kowloon, Hong Kong Al rights reserved. Printed in China ~ NHL Model No. 231390

Tree Storage

1. Remove the tree’s main extension cord plug from the wall outiet.

2. Starting at the top, disconnect the “TOP” from section “B” and then disconnect section “B” from section “A”. {Fig. 1}
   
   Note: Gently fold the tips in branches and fold the branches up toward the center. {Fig. 2}
   
   Care should be taken to avoid damage to the lights.

3. Remove section “A” from the tree stand and close tree stand to place into the carton.

4. Refer to the drawing on how to repack your tree. {Fig. 3}
   

IMPORTANT: Store your carton neatly in a cool, dry location protected from sunlight to prolong the tree life and to better keep the light sets in working order. Do not place a heavy load on the carton to avoid damage to or crushing the carton and tree inside.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>