TESLA 3 Auto Present Door Handle with LED Installation Guide

TESLA 3 Auto Present Door Handle with LED

Product Information

The Tesla Model 3 and Model Y are electric vehicles designed for efficient and sustainable transportation. These models come with advanced features and technology to provide a seamless driving experience.

Installation Instructions

1. Remove the trim parts and screws as shown in the manual.
2. Take off the horn cover illustrated in Figure A.
3. Leverage the door plate from the indicated position.
4. For the Model 3, remove the circled screws.
5. For Model Y models, remove the screws in the blue circle. The screws in the red circle do not need to be removed.
6. Carefully pick off the socket in the red circle. Note that a sharp-tongued camera can be used to easily pull out the socket from the snaps.
7. Remove the glass tape.
8. After removing the waterproof glue plug, drop the glass to expose the screw. Loosen the screw and take out the glass. It is recommended to mark the lifting height of the glass with a piece of tape before removal for easier reinstallation later.
9. For Model 3, loosen the screws in the ring to install the next handle.
10. Remove the waterproof glue plug in the ring and release three grains. Hold the handle screws and take out the original handle.
11. Remove the original car hall induction parts and install them on our hand. Note that for the left door of the original car, use our left hand, and for the right door of the original car, use our right hand. Incorrect installation may prevent opening of the door.
12. Remove the original car decorative strip and install it on our hand. The decorative strip has three buckles, with the top buckle located at the back of the handle.
13. Insert the corresponding colored line into the corresponding original car mother seat after carefully identifying the color and letter number.
14. Insert the corresponding colored line into the corresponding original car male seat after carefully identifying the color and letter number.
15. If the left rear door and right rear door are installed in serial number 14 and 15 for Model Y, this transfer wire is not required.
16. Remove the screws, clips, and decorative panels in the three parts of the front passenger box.
17. Remove the buckle from the first driver and then pull out the decorative board at B. Note that the main driving decorative board is removed in the same way as the first passenger.
18. Remove the decorative panels of the main driver and the passenger driver under the center of the original car channel to facilitate the line of the left front door and the left rear door. Bundle the CAN protocol harness of Model 3 pass from below the center.
19. For 2021 Model 3 and Model Y, connect the power supply positive line to the battery positive pole in the front cover. Route it from position A to the deputy driver in the car. The negative pole should be connected to the original car.
20. For 2020 Model 3, connect the CAN Protocol Cable to Main Driver.
21. For 2021 Model 3 and Model Y, connect to the socket of the passenger speaker host. Before pulling out the speaker socket, turn off the power from the central control screen to prevent damage to the speaker host.

INSTALLATION INSTRUCTION

1. Remove the ①②③ trim parts and above screws shown above

2. Remove the horn cover in figure A

3. Leverage the door plate from the ① position above

4. The model _3 model removes the circledscrews

5. MODEL Y models remove the screws in the blue circle , the screws in the red circle do not need to remove

6. pick off the red circle in the socket(note that the socket can be inserted into the snaps witha sharp -tongued camera can be easily pulled out )

7. Remove the glass tape

8. After removing the waterproof glue plug in the ring , drop the glass to the visible screw, loosen the screw and take out the glass
   (Suggestion : before taking out the glass , it isbest to stick a piece of tape on the relative position of the glass to mark the lifting height, so as to facilitate the loading after the completion of the glass separation.

9. MODEL – 3 model should loosen the screws in the ring to install the next handle

10. Remove the waterproof glue plug in the ring and release three grains Hold the handle screws and take out the original h a ndle

11. remove the original car hall induction parts in the circle and install them on our hand
    Tip: the original car hall induction parts, the left door of the original car hall induction parts with our left hand, the original car right door of the Hall should be installed with our right hand, the wrong will not open the door

12. remove the original car decorative strip to install to our hand
    Tip: decorative strip has three buckle from the back of the handle top buckle can be

13. four door wiring harness of MODEL 3 can be wired from the ring crest tube. MODELY The front left door and the front right door can be wired from the peak tube in the circle, the rear left door and the rear right door from the special female transfer socket matching with the goods, see the next serial number 14, 15 figure

14. First carefully look at the color of the line and the corresponding letter number, and then insert into the corresponding original car mother seat

15. First carefully look at the color of the line and the corresponding letter number, and then insert into the corresponding original car male seat

16. MODEL Y If the left rear door and right rear door are installed in serial number 14 and 15, this transfer wire is not required

17. Remove the screws, clips and decorative panels in the three parts of the front passenger box

18. remove the buckle from the first driver and then pull out the decorative board at B
    Tip: The main driving decorative board is removed in the same way as the first passenger

19. Remove the decorative panels of the main driver and the passenger driver under the center of the original car channel to facilitate the line of the left front door and the left rear door
    The bundle and the CAN protocol harness of 20 MODEL _3 pass from below the center.

20. 2021 MODEL 3 and MODEL Y power supply positive line is connected to the battery positive pole in the front cover, from the hole position in A to the deputy driver in the car, and the negative pole is connected to the original car

21. 2020 models MODEL_3 power supply positive terminal connected to the passenger side, as shown in the figure, the negative terminal connected to the lap iron earth
22. 2020 MODEL 3 CAN Protocol Cable to Main Driver

23. 2021 MODEL – 3 and MODEL Y connected to the socket of the passenger speaker host prompt: before pulling out the speaker socket, turn off the power from the central control screen to prevent damage to the speaker host.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>