Berker 85265100 Conventional Electronic Platform User Manual
- June 13, 2024
- Berker
Table of Contents
Berker 85265100 Conventional Electronic Platform User Manual
Operation instructions
Caution :
- This unit is to be installed by a qualified professional only according to the installation standard in force in the country.
- Each output can control only one motor.
The device is a waterproof mains powered-up radio receiver. It receives KNX radio controls to control the opening it connected to its terminals. It allows to control the openings such as rolling shutters, awning blinds, blinds with slats … The device can be controlled remotely via radio transmitters (e.g. flush-mounted devices, radio push-buttons, hand-held transmitters).
Caption
- Button and J configuration LED
- Button and LED feature K of the raising output ▲ and of the lowering output ▼
- Connector block.
Features
- 1 shutter/roller channel controlled by KNX radio.
- 2 volt-free contacts µ10 A, 230 Vv AC-1.
Operation :
- Availability of manual control Raising / Lowering from buttons K 2 and 3.
- Display of output state on LED fct 2 and 3 (red light ON = relay closed)
The specific features of each product depend on configuration and set-up.
Configuration
The device may be configured in 3 different ways :
- quicklink & : configuration without tool, directly on the device via buttons J and K (see configuration instructions quicklink& )
- tebis TX : configuration using connection device from Hager
- ETS3/ETS4 via KNX-RF/TP gateway : database and description of software application available from the Manufacturer.
In order to change the configuration mode, a reset to factory settings is obligatory.
Repeater feature
It increases the system radio range thanks to re-transmission of messages
received by the product.
It is inactive by default and can be enabled/ disabled by pressing once > 2 s
J button on product power-on.
cfg LED flashing on power-on signals that the feature is active.
Reset to factory settings
Maintain J button down until LED cfg flickers >10 s, then release. cfg LED
turns OFF to signal Factory Reset end.
This operation overwrites the entire product configuration in any
configuration mode.
After power switch-on or a reset to factory settings, wait for 15 s before to
do a new configuration.
Correct Disposal of This product (Waste Electrical & Electronic Equipment).
(Applicable in the European Union and other European countries with separate
collection systems).
This marking shown on the product or its literature indicates that it hould
not be disposed with other household wasted at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes of disposal.
Technical characteristics
Versorgungs- spannung| Supply voltage| Tensione di alimentazione| 230V~
+10%/-15%240V~ +/-6%
---|---|---|---
Sendefrequenz| Transmission frequency| Frequenza portante| 868,3 MHz
Abmessungen| Dimensions| Ingombro| 150 x 85 x 35 mm
Verzögerungszeit bei 2 entgegengesetzten Richtungen| Delay timebetween 2
opposite directions| Temporizzazione tra i due movimenti in senso opposto| 600
ms
Schutzart| Degree ofprotection| Grado diprotezione| IP 55
Betriebs- temperatur| Operating temperature| Temperatura di funzionamento| -10
… +55 °C
Lagertemperatur| Storage temperature| Temperature di| -20 … +70 °C
Vorsicherung: 10A| Upstream protection : circuit breaker 10A| monte : 10A|
10A
Maxima| Max operating altitude| Altitudinal| 2000m
Sender| Emission power| Potenza| 25mW max
Stil stand| Transmission mode| Modality| KNX RF1.R
Categories| Receiver category| cate| 2
Sender| Transmitter duty cycle| del| 1%
Electric connection :V 
0,75 … 2,5 mm2
Usable throughout Europe and in Switzerland Hager Controls hereby
declares that the KNX-RF blind actuator 1gang surface-mounted device complies
with the essential requirements and other relevant provisions of Directive
2014/53/EU.
The CE declaration is available on the:
www.hagergroup.com
Berker GmbH & Co. Germany – Tel.: +49 6842 945 0 – Fax: +49 6842 945
4625 – E-Mail: info@berker.de – www.berker.com
Berker GmbH & Co.
KG – Zum Gunterstal
Blieskastel/Germany 66440
Tel : 0 945 6842 49+
Fax : 4625 945 6842 49
E-Mail: info@berker.de
www.berker.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>