Berker KNX-RF Binary input 2-gang 230 V Flush-mounted Instruction Manual
- June 4, 2024
- Berker
Table of Contents
- Berker KNX-RF Binary input 2-gang 230 V Flush-mounted
- Caption
- Features
- Operation of cfg-LED 3
- Wiring, test and start-up
- Configuration
- Reset to factory settings
- Correct Disposal of this product
- Technical characteristics
- Berker GmbH & Co. KG
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Berker KNX-RF Binary input 2-gang 230 V Flush-mounted
The device is a mains powered-up radio transmitter, designed to interface contacts free of potential with a KNX bus. This device allows to the provision of communication feature for push buttons, switches or other conventional automation contacts.
Caption
- Mains power supply connector block.
- Button and configuration LED.
- Connector with inputs connection wire (length 20 cm).
Features
- 2 independent channels
- 230 V power supply
Operation of cfg-LED 3
- LED flickers for 1s when pressed: the product is not configured.
- The LED goes on for 100 ms after pressing: input is configured, and control is transmitted.
- The specific functions of this product are defined in its configuration and set-up.
Wiring, test and start-up
- The modules are installed in a flush-mounting box of 60 mm diameter in connection with a pushbutton or a switch.
- Depth will depend on the type of equipment used. The length of connection shall not exceed 10 m. Wire not used shall be isolated.
Configuration
The device may be configured in 3 different ways
- quicklink & : configuration without tool, directly on the device via button and LED (see configuration instructions quicklink& )
- tebis TX: configuration using connection device from Hager
- ETS3/ETS4 via KNX-RF/TP gateway: application, product database, and documentation available from the manufacturer.
Configuration by ETS
- Press the button for addressing by means of the KNX-RF/TP gateway.
- In order to change the configuration mode, a reset to factory settings is obligatory.
Reset to factory settings
- Maintain button down until LED cfg flickers >10 s, then release. cfg LED turns OFF to signal Factory Reset end.
- This operation removes the entire product configuration in any configuration mode.
- After power switch-on or a reset to factory settings, wait for 15 s before doing a new configuration.
Usable throughout Europe CE and in Switzerland
Hager Controls hereby declares that the 2 radio inputs module device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. The CE declaration is available on the www.hagergroup.com site
Correct Disposal of this product
(Waste Electrical & Electronic Equipment).
(Applicable in the European Union and other European countries with separate
collection systems).
This marking shown on the product or its literature indicates that it should not be disposed with other household waste at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this device for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes of disposal.
Warning
- This unit is to be installed by a qualified professional only according to the installation standard in force in the country.
- Cut off 230V power supply to the product before connection of or operation on the inputs.
- Not suitable for outside installation.
Technical characteristics
Berker GmbH & Co. KG
- ADDRESS: Zum Gunterstal – 66440 Blieskastel/Germany
- Tel: +49 6842 945 0
- Fax: +49 6842 945 4625
- E-Mail: info@berker.de
- www.berker.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>