FRONT RUNNER F RRAC248 Pro Water Tank Surface Mount Bracket Instructions

: June 13, 2024
: Front Runner

Table of Contents

BornToRoam Share your adventures on:

FRONT RUNNER F RRAC248 Pro Water Tank Surface Mount Bracket Instructions

READ ME !

Thank you for purchasing a Front Runner Pro Water Tank Flat Mount Bracket.Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components. Refer to Page 2 for a list of all the components, quantities and tools required.

IMPORTANT WARNING

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions. Please call us if you have any questions about the installation of this product.

CHECK ONLINE FOR THE LATEST FITMENT GUIDE

GET ORGANIZED

IN THE BOX

1| 1x| Mounting Bracket
2| 3x| M6 x 25 Button Head Screw
3| 4x| M6 Jack Nut
4| 1x| Jack Nut Tool
5| 3x| M6 Nyloc Nut
6| 3x| M6 x 19 x 1.2 Flat Washer
7| 2x| PSA Strip PE60 (420mm)
8| 1x| M6 x 30 Button Head Screw

TOOLS NEEDED

10mm 13mm24mm
4mm5mm
mm 6.5mm 12mm
Marker
Denatured Alchohol
AntiRust
Sealant
Thread Tape

FIGURE 1.1

FIT AND SECURE

2.1

5mm

13mm
Assemble A, B and C (supplied with RRAC179) to the Mounting Bracket (Item 1).
2.2
Water Tank Parts
Marker

4mm6.5mm12mm
Determine where the Pro Water Tank (Sold Seperately) will be Mounted. Looslyfit the Pro Tank Strap (Sold Seperately) andPro Water Tank (Sold Seperately) to the Mounting Bracket (Item 1).

Mark holes (D) as shown

Option A
Drill a 4mm Pilot hole and open to 6.5mm if you want to Secure the Mounting Bracket using M6 x 25 Button Head Bolt, M6 x 19 x1.2 Flat Washer and M6 Nyloc Nuts (Items 2, 5 & 6).

Option B
Drill a 4mm Pilot hole and open to 12mm if you want to Secure the Mounting Bracket using M6 x 25 Button Head Bolts and M6 Jack Nuts (Items 2 & 3). Apply anti-rust before 2.3.

2.3

4mm

Only Proceed with this step when using mounting option B
Insert an M6 x 30 Button Head Bolt (Item 8) into the side of the Jack Nut Tool (Item 4). Loosely fit a jack nut (Item 3) to the buttonhead bolt as shown. Insert the Jack Nut (Item 3) into the 12mm hole.

Using a cordless driver and a 4mm allen cordless bit, set the jack nut into the hole while holding onto the handle of the Jack Nut Tool (Item 4).

Repeat for the other holes.

2.4

4mm
**
10mm

AntiRust

Sealant
**
Apply anti-rust around all the holes. Placesome silicone around each hole.

Option A
Secure the Pro Tank Strap (Sold Seperately) and the Mounting Bracket (Item 1) usingM6 x 25 Button Head Bolt, M6 x 19 x 1.2 FlatWashers and M6 Nyloc Nuts (Items 2, 5 & 6).

Option B
Secure the Pro Tank Strap (Sold Seperately) and the Mounting Bracket (Item 1) using M6x 25 Button Head Bolts (Item 2).

**2.5
Remove the Backing and stick
Denatured Alchohol