spaDepot Blaster 1000 Automatic Spa Filter Cleaner Instructions
- June 13, 2024
- spaDepot
Table of Contents
SpaDepot.com
Blaster 1000™
AUTOMATIC FILTER CLEANER INSTRUCTIONS
Blaster 1000 Automatic Spa Filter Cleaner
Congratulations on purchasing the BLASTER 1000™ Automatic Filter Cleaner.
Cleaning your dirty pool filter will now be a whole lot easier. Taking just a
few minutes, the BLASTER 1000™ will clean your filter by automatically
rotating it while PowerJets blast focused water to clean the filter pleats.
The BLASTER 1000™ is designed to accommodate cartridge filters up to 20” in
length.
Follow the steps below to get started:
-
Connect Hose
Attach a garden hose to the swivel nut hose fitting.
Turn the swivel nut counter-clockwise to tighten. -
Add Nozzle Covers (If needed)
Attach nozzle covers to close off unneeded PowerJets. This will also increase the pressure available to the remaining PowerJets.
Use firm pressure to press the nozzle cover on from directly above the PowerJet nozzle. -
Place Filter
Place your dirty filter on the center support rods as shown.
Make sure the flanges of the filter are resting on the center support rods. -
Add Spray Covers (If needed)
Attach spray covers as needed to block the spray from coming from the area not covered by your filter.
Attach the spray covers to the top outer frame tubes. Leave unused spray covers on the bottom frame tubes. -
Turn Water On
Turn the water on at the spigot and gradually open to full pressure.
The water will spray from the PowerJets, and your filter will begin to rotate. -
The Cleaning Begins
The BLASTER 1000™ will now automatically clean your filter. The process normally takes between 3 – 8 minutes depending on how dirty your filter is.
When no more debris is seen in the runoff water your filter is clean.
TROUBLESHOOTING
Spray Power Insufficient| If there is insufficient pressure coming from the
PowerJets, try closing off some PowerJets by adding more nozzle covers (Step
2). This will increase the water pressure available to the remaining
PowerJets.
---|---
If the flow rate is too low try using a different faucet where the water
pressure might be higher. Typically, faucets near the front of the house or
main line have better flow rates.
If the flow rate is too low try using a different faucet where the water
pressure might be higher. Typically, faucets near the front of the house or
main line have better flow rates.
Filter Does Not Rotate| Check to see that your filter has round flanges.
Flanges that have other geometrical shapes or flanges that have handle tabs
will not rotate.
Make sure all filter pleats are wet first. A dry filter will get soaked on one
side first and the unbalanced weight can prevent the filter from making a
complete a rotation.
Heavy filters might have difficulty properly gripping the support rods. If
the support rods are turning and the filter is not rotating, try using grip
sleeves (not included with the Blaster 1000). Call Neoterics for support.
Water leaks during use| It is normal to observe some water escaping from
around the support rods – the unit design allows for this and it will not
affect the performance. With higher water pressures some water may also
escape from around other seals and the main housing, but this too will not
affect the unit’s performance.
Water stays in device| There is a small drain hole in the bottom of the main
housing to help drain the water left in the unit after use. You can turn the
nozzles down on the PowerJet to drain the water more quickly. However, there
will always be some water that remains in the device after use.
ONE YEAR LIMITED WARRANTY
Your new product is warranted to the original consumer against defects or
workmanship and materials for a period of one year from the original purchase
date. Should there be a defect or malfunction of this product, Neoterics will
repair or replace the product, at Neoterics’ option, free of charge other than
the postage required.
This warranty is void if the product has been subject to damage, unreasonable
use, improper service, or other causes not arising from defects in original
material or workmanship. There are no expressed warranties other than those
stated herein.
Any expressed or implied warranties, including but not limited to
merchantability and fitness for a particular purpose are limited to the above
one-year warranty period. Neoterics shall not be liable for any incidental or
consequential cost, expenses or damages resulting from any failure defect or
malfunction of this product.
This warranty grants you specific legal rights, and you may also have other
rights that vary from state to state.
Available for purchase from:
The Spa Depot
www.SpaDepot.com
800-823-3638 6AM – 5PM Pacific
Time
References
- SpaDepot.com | America's Favorite Hot Tub Supply Store
- Hot Tubs, Spas, Hot Tub Covers, Spa Chemicals | SpaDepot.com
- SpaDepot.com | America's Favorite Hot Tub Supply Store
- Hot Tubs, Spas, Hot Tub Covers, Spa Chemicals | SpaDepot.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>