spaDepot AC1064 Cover Mate Side Mount Spa Cover Lift Instruction Manual
- June 13, 2024
- spaDepot
Table of Contents
Covermate I Plastic
Installation Instructions
Updated as of 08/30/12
AC1064 Cover Mate Side Mount Spa Cover Lift
Step #1
Position the spa cover (in closed position) on the spa, making sure that all
four corners are properly positioned and square on the spa.
Step #2
Using the #10 x 1” mounting screws, attach the left and right Mounting
Brackets to the appropriate sides of the spa. Caution: to prevent splitting of
wood cabinet, pre-drill holes with a 1/16” drill bit. Mounting height is
optional (see Fig. 1). By positioning the Brackets 8” down from the top of the
spa shell, approx. 9” of clearance behind the spa will be needed. Mounted at
this position approximately 75% of the spa cover will be standing above the
spa surface in the off position. By positioning the Brackets 12” down from the
top of the spa shell, approx. 15” clearance behind the spa will be needed.
Mounted at this position, approximately 50% of the spa cover will be standing
above the spa surface in the off position.
Step #3
Connect the Pivot Arms to the Mounting Brackets (see Fig. 2). After the Pivot
Arms are connected, tilt them back into the upright position.
Step #4
Insert the long end of the Support Arms into the Center Coupler piece. Then
slide the Support Arms into the Pivot Arms (see Fig. 3).
Step #5
Lay the Covermate on the spa cover. Adjust the Center Coupler piece and
Support Arms so that the Center Coupler is laying parallel to the spa cover’s
hinge about 1/2” away (see Fig. 4). Using the #10 self tapping screws, fasten
the Support Arms to the Pivot Arms and the Center Coupler piece. Note: Be sure
to rotate the Center Coupler so that the inserted screws are at a horizontal
angle with the heads facing the back of the spa.
Step #6
Slip the black hand grips to the edge of the spa cover and snap the Small
Black Dome Caps on the heads of all exposed #10 screw heads. Push the 7/16”
plug into the unused bracket (H) hole.
Step #7
Attach the provided 3 hook TowelMate on the preferred side of your Covermate
by simply snapping it into place and inserting the middle self tapping screw
(see Fig. 5).
CAUTION!
Do not use the Covermate in high wind condition. Injury from the spa cover
being blown over and impacting the spa user can occur.
ITEM | PART# | DESCRIPTION | QTY |
---|---|---|---|
A | 100001 | SUPPORT ARM | 2 |
B | 100002 | FOAM GRIP | 2 |
C | 100003 | CENTER COUPLER | 1 |
D1 | 100004 | PIVOT ARM | 2 |
E | 100007 | PIVOT ARM CAP | 2 |
F1 | 100344 | BUSHING | 4 |
H | 100021 | MOUNTING BRACKET | 2 |
I | 100008 | TOWELMATE | 1 |
K | 100010 | 3/8 X 3″ HEX CAP BOLT | 2 |
L | 100011 | 3/8 NYLON LOCKNUT | 2 |
M | 100012 | 3/8 FLAT WASHER | 4 |
N | 100013 | #10 X 5/8″ SELF TAPPING SCREWS | 12 |
O | 100014 | #10 X 1″ MOUNTING SCREWS | 24 |
P | 100015 | LARGE BLACK DOME CAP | 2 |
Q | 100016 | SMALL BLACK DOME CAP | 36 |
R | 100347 | 7/16″ PLUG | 2 |
CMI-PLAST 120830
SpaDepot.com
References
- SpaDepot.com | America's Favorite Hot Tub Supply Store
- SpaDepot.com | America's Favorite Hot Tub Supply Store
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>