bol QQ003 WiFi Pet Feeder User Manual
- June 13, 2024
- bol
Table of Contents
bol QQ003 WiFi Pet Feeder User Manual
Hardware installation and introduction
Insert the type-C USB power cord into the connector on the bottom of the feeder. Open the battery compartment, insert 4 pieces of AA batteries, so that the feeder can still work automatically even without external power supply.
Battery
The back-up battery is designed for short-term alternative when the external power is cut. When there is battery only, the feeder will be in sleep mode after 3 minutes of no operation. When in sleep mode, the network and all the operations on the App will be unavailable. The feeder will still feed normally at the schedule feeding time.
Notice:
Rechargeable batteries are not recommended. Rechargeable batteries may case
inaccurate power indications.
Rotate the bucket to lock the grain bucket to the feeder’s main body.
Put the desiccant pack into the drying box on the top cover. Unlock the lock on the cover to install the cover. Then place the feeding tray into the feeder from the bottom.
Operation panel introduction:
Notice: For your pet’s health, please wash the grain bucket and feeding tray regularly. The feeder body should not be filled with water. Please use a wring-able wet cloth to wipe.
Software Installation
Add pet feeder via Bluetooth
1. Before App operation, please enable the mobile phone’s Bluetooth function.
2. Search the App Store or scan the QR code below to download and install Pet Zero.
3. Run the App, read and agree to the privacy policy, and register a new account or login to a registered account. When you register or login to the account, please choose the correct country or area.
4. Click A dd Device or + to add a new pet feeder. Then the App may ask you to access certain permissions and turn on Bluetooth which mentioned in step 1. These permissions are very important for the App, so please allow them and turn on Bluetooth.
5. Power on the feeder, check whether the feeder’s indicator is flashing once
every 3 seconds. If the current indicator LED is in any other state, please
press and hold the config button for about 5 seconds to reset the feeder.
Then mobile phone will detect the feeder by Bluetooth automatically. Once
detected, App will show a message to ask to add the feeder. If not, please
check the feeder’s indicator LED carefully. Click Add and ( + )
button.
Indicator LED status:
6. Then please fill in the Wi-Fi network information. The name of Wi-Fi
network will appear in the textbox automatically.
Please note that the feeder does not support 5Ghz Wi-Fi networks, it support
only 2.4Ghz networks. Please check that the Wi-Fi name is the name of a 2.4Ghz
Wi-Fi network. If not, please switch the mobile phone’s Wi-Fi network to a
2.4Ghz Wi-Fi network.
Next, please enter the Wi-Fi password and click Next.
Important Notice:
a. Please choose a 2.4Ghz Wi-Fi signal instead of a 5Ghz signal. The feeder
does not support 5Ghz Wi-Fi networks.
b. When entering the password, be aware that it is case sensitive.
c. Make sure the feeder is not far away from router and reboot router to try
again.
d. Please choose a Wi-Fi network with WPA or WPA2 encryption instead of WEP
encryption.
e. Make sure that MAC address filtering and wireless device isolation is
turned off on the wireless router.
f. The feeder may not support the Wi-Fi signal of the wireless repeater. If
the connection fails, try connecting to the wireless router.
7. The feeder will then try to connect to the Wi-Fi network. Waiting the
feeder connected to the Wi-Fi and click Done to complete adding process.
If the feeder fails to connect, please check the important notice above first.
Add pet feeder via AP mode
1. If the feeder fails to connect to the Wi-Fi network, the AP mode is plan
B for adding the feeder.
Choose Add manually and choose Pet Feeder AP mode manually in the add
page. Notice that the other 2 options in add manually list are not suit for
this feeder, please do not choose them.
Fill in the 2.4GHz Wi-Fi network information and click Next.
Power on feeder and check that the indicator LED is flashing in RED once every
3 seconds as same with adding feeder by Bluetooth. Then click Next.
2. Then the App will ask you to switch your mobile phone’s network to a new network broadcast by the feeder. Please go to Wi-Fi settings on the mobile phone and connect to the Wi-Fi which starts with SmartLife- . No password is necessary.
3. Return to the App after the Wi-Fi is connected. The adding process is the same as in normal mode covered above.
Feeding
Manual feeding
1. Enter feeder’s main interface. Choose the feeding portions and click Feed. The feeder will feed immediately.
Timed feeding
1. The pet feeder supports the scheduled feeding of exact portions at exact times. Click Meal plan and Add , choose feeding time , repeat rules for each day of the week , and feed portions , then click Save.
2. The feeder supports up to 10 feeding schedules. If you need to disable a schedule, you can disable it by disable its switch. You can also delete it by long press feeding schedule to access the delete option.
Feeding records and alarm
1. After feeding, there will be feeding records in the App. Click Feeding record to check the feeding history. The feeding records of the last 7 days will be shown.
2. When battery level is low or food stuck in feeder, a message will appear in the App. And you can check warning messages in feeder page and the message center.
Others
Common settings
Click to access the common settings page.
Device information: Check feeder information. Please make sure the time zone
of the feeder is correct. It should be same as the mobile phone’s time zone
when adding the feeder. If it is incorrect, the feeder may feed at incorrect
times, so please remove the feeder and add it again.
Offline Notification: When the feeder is offline, a notification will send to your mobile phone.
Share Device: If you want to add the feeder to another mobile phone, register a new account on the new mobile phone, then share the device with the new account. Please make sure that both 2 accounts are in the same country or area when registering them.
Remove Device: There are 2 options that will both remove the device from the App. You could re-configure the feeder’s Wi-Fi network using these 2 options. If you wish to remove all the settings in the feeder, choose Disconnect and wipe data.
FAQ
Q: Why did the feeder fail to connect to my Wi-Fi network?
A: Please check the important notice on Page 6 for help. You can try to add
the feeder via Bluetooth mode instead of normal mode.
Q: Why does the feeder feed at the wrong time?
A: Please check that the time zone of the feeder is correct. You can find help
about time zone information on page 12.
Q: Why the indicator LED is always off?
A: There are 2 reasons. The indicator LED will be turned off when the feeder
is only powered by battery. The indicator LED could also be disabled manually
in settings.
Q: Why my feeder could not connect to Internet when it is only powered by battery.
A: When there is battery supply only, the feeder will be in sleep mode after 3 minutes of no operation. When in sleep mode, the network and all the operations on the App will be unavailable. The feeder will still feed normally at the schedule feeding time.
Reset
To restore the feeder to factory default setting, please power on the feeder,
and long press the config button for 5 seconds. When the feeder’s indicator
LED is flashing once every 3 seconds, it is reset.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>