TESLA PC501WD Heater Convector Panel User Manual

TESLA PC501WD Heater Convector Panel

Product Information

• Product Name: Panel Heater
• Model: PC501WD

Product Technical Parameters

• Voltage: ~230 V / 50 Hz
• Power: 2000W
• Dimensions: Length 87.0 cm, Width 8.0 cm, Height 43 cm
• Weight: N.W. 5.6 kg, G.W. 6.6 kg

Product Usage Instructions

• You must obey common safety guidelines when using electrical products, especially in the presence of children.
• To avoid electric shock or damage due to the heat, always make sure the plug is pulled out before the heater is moved or cleaned.
• In order to avoid overheating, do not cover the heater.
• Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present. The heater must not be located immediately below a socket outlet.
• Do not use this heater in the immediate surroundings of a bath, a shower, or a swimming pool.
• In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

Assembly Instructions

For Wall Mounted

1. Keep a distance of at least 30cm between the heater and floor, wall, etc.
2. Use a drill dimension paper to drill the top two holes on the wall and insert the expansion screws.
3. The hook racks are pre-assembled on the back of the heater. Hang the top two hook racks on the screws. Mark the position of the two bottom hook racks on the wall. Drill the bottom two holes on the wall and insert the expansion screw’s plastic cover.
4. Hang the heater on the wall and insert the expansion screws in the bottom two holes.

For Stand

1. Fit the foot onto the bottom of the heater body.
2. Fasten the foot with 4 screws.

IMPORTANT SAFETY INFORMATION

You must obey common safety guidelines when using electrical products, especially in the presence of children.

WARNING! To avoid electric shock or damage due to the heat, always make sure the plug is pulled out before the heater is moved or cleaned.
WARNING! In order to avoid overheating, do not cover the heater ”Do not cover”.
CAUTION! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present. The heater must not be located immediately below a socket outlet.
CAUTION! Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool. Regarding the instructions of the method on how to fix the feet to the heater, thanks to refer to the section “ASSEMBLY”.
CAUTION! In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

• The product is intended for home use only.
• Make sure the heater is connected to the house’s regular mains (230 V), as it indicated on the heater.
• New heaters will produce a specific odor when used the first time. This will stop after a short time and is completely harmless.
• Check for any pieces of packing foam or cardboard that may have fallen into the heating elements of the heater. These pieces must be removed in order to avoid unpleasant odors.
• Always turn off the heater and unplug it when not used for a long time.
• Pay special attention if the heater is used in rooms where children, the handicapped or elderly reside.
• The heater should not be set up directly beneath an electrical socket outlet.
• The cord must not be laid under any kind of carpet. Make sure the cord is laid in such a way that nobody can trip on it.
• The heater must not be used if either the cord or plug is damaged. The heater must not be used if it has been dropped on the floor or is damaged in any other way causing it to malfunction.
• The cord must be repaired by the manufacturer or by an expert if it has been damaged, to avoid dangerous situations.
• Avoid using extension cords, which may overheat and could possibly start a fire.
• Never cover the air vents on the heater. Avoid potential fire hazards by making sure the air intakes are not blocked or covered. The heater should be used in rooms with normal flat floors.
• The heater should not be installed in close proximity to flammable materials of any kind because there can always be a risk of fire.
• The heater must never be used in rooms where gasoline, paint or other flammable liquids are stored, such as in a garage.
• Never touch an electric heater with wet hands. The heater should be installed so a person showering or taking a bath cannot come into direct contact with it.
• The heater becomes hot when it is on. Therefore, be careful and avoid burning or scorching your skin.
• The heater must be switched off, the plug removed and the heater must cool down before it is moved.
• Avoid overloading the mains (the circuit) where the heater is connected. The heater may overload the electrical circuit if other electrical devices are plugged into the same socket outlet.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved
• Children should not play with the device. Cleaning and maintenance should not be done by unsupervised children.
• Children under the age of 3 should be kept away from the device, unless they are under constant supervision.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance

TECHNICAL PARAMETER

Model| Voltage| Power (W)| Length| Width| Height| N.W.| G.W.
---|---|---|---|---|---|---|---
PC501WD| ~230 V / 50 Hz| 2000W| 87.0 cm| 8.0cm| 43cm| 5.6 kg| 6.6 kg

DESCRIPTION OF THE HEATER

ASSEMBLY

For wall mounted

1. Be sure to keep the distance between the heater and floor, wall and so on at least 30cm as picture (1).
2. Use drill dimension paper to drill top two holes (Φ8) on the wall and put the expansion screws in the holes as picture (2).
3. The hook racks are pre-assembled on the back of the heater, hang the top two hook racks on the screws as picture (3). Mark the two bottom hook racks’ position on the wall and take away the heater, then drill bottom two holes (Φ8) on the wall and put expansion screw’s plastic cover in the holes as picture (3).
4. Hang the heater on the wall and put the expansion screws in the bottom two holes as picture (4).

For Stand

1. Fit the foot onto the bottom of the body.
2. Fasten the foot with 4 screws.

ELECTRONIC THERMOSTAT INSTRUCTIONS

Control panel for electronic thermostat:

1. Display (show the desired room temperature by default)
2. Control button (Increase)
3. Timer indicator light
4. Power indicator light
5. Control button (Reduce)
6. Timer/Open window function button
7. Off/Stand by button

WARNING!

• Before the heater is turned on, it must be attached to a wall or stand. If the heater is not installed correctly or is installed askew, this may cause the heater to malfunction or in the worst case, be damaged.
• If the temperature sensor is not functioning properly, you will see the symbol below on the display. Please contact the dealer or importer.

OPERATIONS

Turn on:
Plug in and switch on the heater, the heater will enter into standby mode, and show “OF” on display. Press button to turn on the heater, and show factory default setting temperature 22°C on display.

Temperature setting:

• Temperature setting range is 5–35°C.
• Default temperature setting is 22°C.
• Press or button to set temperature, the temperature will increase or decrease by 1°C after each pressing. It will show setting temperature on display after setting.

Timer:

• Press button, “ ” flash on display, then press or button to set timer. Each pressing is 1 hour. Press button to save setting, or wait 15 seconds to save automatically. Timer indicator light will keep on red after setting.
• Timer set range is 0 to 24 hours.
• Press button again to modify or cancel timer setting.
• After timer close, the heater will enter into standby mode, and press button to turn on the heater.

Open window function

• The heater has an open window function.
• Default setting of open window function is closed.
• Press and hold button for 5 seconds, display show “F0”, then press button to open open window function, display show “ON”, and press button to close open window function, display show “OF”, then press button to save setting, or wait 15 seconds to save automatically.
• Open window function description:
  • If you open a window widely in the space where the heater is located and the temperature drop 2°C or more than 2°C in two minutes, a sensor will detect the sharp drop in temperature. The heater will switch out automatically and show “F0” in display.
  • The heater will be reignited automatically after 10 minutes. However you can manually relight the heater before the 10 minutes end by pressing . The icon “ ” disappears and show previous operation mode.

Resetting the heater

• Turn off the heater’s main switch.
• Press and hold while you turn on the heater’s main switch.

MAINTENANCE

• For cleaning, always unplug the heater and leave it to cool.
• Wipe the heater regularly with a damp cloth and dry the surface before turning on the heater again.
• The heater must be cleaned at least once a month during the heating season.

CAUTION!

• The heater should never be immersed in water. Avoid using detergents to clean the heater.
• Never let any water get inside the heater; this can be hazardous. Dust etc. should be removed with a soft cloth.
• The heater can be stored in a dry and clean place.

Waste disposal
The symbol indicates that this product is not to be disposed of together with household waste. This product must be delivered to a recycling service or container for electrical appliances and electronic equipment. This is done to avoid health risks and prevent harm to the environment. Local businesses (or the environmental station in your neighborhood) are required by law to accept and recycle such products, as a means of environmentally sound disposal. tesla.info.

References

• Tesla.info | Technology for all

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>