esse-ti 7IS-80588 Helpy Phone Naked User Guide

: June 13, 2024
: esse-ti

Table of Contents

esse-ti 7IS-80588 Helpy Phone Naked
INSERTING SIM CARD
CONNECTIONS
PARAMETER SETTING VIA SMS
PARAMETER SETTING VIA PC
OPERATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HELPY PHONE NAKED
GUIDA RAPIDA PER L’UTENTE
USER QUICK GUIDE

esse-ti 7IS-80588 Helpy Phone Naked

Helpy Phone Naked is an automatic telephone set wich allows to set up a handsfree communication with previously-programmed telephone numbers upon pressing a pushbutton. Helpy Phone Naked answers incoming calls, automatically or upon pressing a pushbutton, and allows room-monitoring. For correct operation, a SIM card enabled for voice calls and SMS is required. Helpy Phone Naked is available with a built-in antenna or with an external antenna (2 m ). esse-ti 7IS-80588 Helpy Phone Naked - PHONE Main features and characteristics

Power supply: via USB (using an USB-C cable not supplied)
3,7 V 1150 mAh rechargeable LiPo battery
Basic programming: via SMS
Advanced programming: via PC (software: Helpy Phone Assistant)
Phonebook 12 listings
Room monitor
LED signalling GSM signal strength: red
LED signalling alarm sent: yellow
LED signalling alarm received: green

INSERTING SIM CARD

➢ Open the Helpy Phone (use a credit card by sliding it from the top along the side hole). esse-ti 7IS-80588 Helpy Phone Naked -
PHONE1 ➢ Insert the micro-SIM card with the contacts facing down (the PIN code of the SIM card must be removed before inserting). ➢ Remove the adhesive label applied to the battery contacts.
➢ Close the Helpy Phone (press until you hear it click).
Once closed, the Helpy Phone automatically switches on.

CONNECTIONS

➢ In case of external antenna, connect the antenna cable. ➢ To power Helpy Phone, connect a cable USB-C to the USB port. esse-ti 7IS-80588 Helpy Phone
Naked - PHONE4

PARAMETER SETTING VIA SMS

Below is the list of message texts required to configure remotely the Helpy Phone.
SMS configuration can be effected by any mobile phone or other tool providing SMS-sending capability.
WARNING
SMS settings effected via Internet might not be successfully sent if the required text format is not respected.
A return SMS will be sent by Helpy Phone delivering confirmation notification.
Ex.
SMS to enable automatic answer: Et.ho:0:391;
SMS notifying the accepted command: 39OK;
SMS notifying the rejected command: 39E05;
Telephone numbers to be called upon pressing pushbutton
First number:
Et.ho:0:01telephone_number110000000;
Second number:
Et.ho:0:02telephone_number110000000;
Third number:
Et.ho:0:03telephone_number110000000;
Fourth number:
Et.ho:0:04telephone_number110000000;
Fifth number:
Et.ho:0:05telephone_number110000000;
Sixth number:
Et.ho:0:06telephone_number110000000;
Activating notification SMS in case of low battery
Parameter: telephone number appointed for SMS notifications of low battery
Et.ho:0:07telephone_number200100000;
Activating room monitoring functionality
Parameter: telephone number enabled to use the room monitoring functionality
Et.ho:0:12telephone_number100000100;
Pushbutton delay
Parameter: from 1 to 10 (seconds)
Factory default: 3 seconds
Lower pushbutton:
Et.ho:0:27parameter;
Upper pushbutton:
Et.ho:0:72parameter;
Automatic answer
Parameter: 1 (enabled) / 0 (disabled)
Factory default: disabled
Et.ho:0:39parameter;
Conversation time
Parameter: from 1 to 60 (minutes)
Factory default: 3 minutes
Et.ho:0:87parameter;
Loudspeaker volume
Parameter: from 1 to 4
Factory default: 3
Et.ho:0:25parameter;
Microphone sensibility
Parameter: from 1 to 4
Factory default: 4
Et.ho:0:36parameter;
Requesting parameter status
Parameter: setting code being queried
Et.ho:0:?parameter;

PARAMETER SETTING VIA PC

Full programming of Helpy Phone can be performed via the dedicated Helpy Phone Assistant software.
Helpy Phone Assistant can be downloaded at the following link: https://www .esse-ti.it

OPERATION

Outgoing call
➢ Press a pushbutton for the set time.
The handsfree is activated and the yellow LED lights up.
The call is automatically sent out to the previously-programmed telephone numbers until it is answered or until the conversation time has elapsed.
When the called party answers, the green LED lights up. The conversation will be interrupted either when one of the two parties terminates the call or when the conversation time has elapsed.
Incoming call (automatic answer is disabled)
Helpy Phone rings like an ordinary telephone set upon an incoming call:
➢ To answer the call, press a pushbutton.
The conversation will be interrupted either when one of the two parties terminates the call or when the conversation time has elapsed.
Incoming call (automatic answer enabled)
Helpy Phone rings upon an incoming call and handsfree connection is automatically established. The conversation will be interrupted either when one of the two parties terminates the call or when the conversation time has elapsed.
Room monitor
➢ Call Helpy Phone from the enabled number.
Helpy Phone answers the call and activates the microphone for environmental monitor purposes.
The conversation will be interrupted either when the calling party terminates the call or when the conversation time has elapsed.
Call end
➢ Press twice a pushbutton during the call.
Volume adjustment
➢ In idle state, press twice a pushbutton.
A tone will be heard.
➢ Repeat the operation until the desired volume level is achieved.