esse-ti 5HK-300 Kone Retrofit Kit Instruction Manual

June 4, 2024
esse-ti

logo

esse-ti 5HK-300 Kone Retrofit Kit

esse-ti 5HK-300 Kone Retrofit Kit product-img

COMPONENTS

esse-ti 5HK-300 Kone Retrofit Kit fig
\(1\)

KRM INSTALLATION

  • Unscrew the 4 screws (shown in the picture) to remove the cover and gain access to the KRM.esse-ti 5HK-300 Kone Retrofit Kit fig \(2\)
  • Disconnect the XS1 and XS2 cables from the KRM board. KRM will turn off.esse-ti 5HK-300 Kone Retrofit Kit fig \(3\)
  • Disconnect the 14-way X12 cable from the KRM board.esse-ti 5HK-300 Kone Retrofit Kit fig \(4\)
  • Connect the X12 cable to the corresponding cable of the retrofit kit (5KT-120).
  • Connect the other end of the retrofit kit cable to the KRM board (X12 connector).
  • Disconnect theRJ11 cable of the telephone line from the KRM board.
  • Sometimes the telephone line is connected directly to the trailing cable (wires n° 15 and 16, often orange and white colors).
  • Connect the telephone line to the RJ11 connector of the retrofit kit.
  • Connect the terminal blocks of the retrofit kit to the Helpy 2W-V 12V MK.
  • Help 2W-V 12V MK can be installed on the top of the car. . Please make sure the microphone is placed in correspondence with a car hole and the audio quality is good.
  • In any case Helpy 2W-V 12V MK can be installed facing upwards.
  • Connect the XS1 and XS2 cables to the KRM board.
  • Help 2W-V 12V MK will turn on (the red LED flashes briefly once every 3 seconds).
  • If KRM starts an alarm, disconnect the XS1 and XS2 cables for few seconds.

Note : for basic programming see the table

Connecting the car-top and car-bottom pushbuttons

  • Disconnect the XS1 and XS2 cables from the KRM board. KRM will turn off.
  • Disconnect the XC9B and XC9C cables from the KRM board.
  • Disconnect the two SPOX connector from the retrofit kit (5KT-120).
  • Insert the two SPOX connectors into the XC9B and XC9C connectors on the KRM board.
  • Connettere i cavi XS1 e XS2 alla scheda KRM. Helpy 2W-V 12V MK si accende (il LED rosso lampeggia una volta ogni 3 secondi).
  • Connect the XS1 and XS2 cables to the KRM board. Helpy 2W-V 12V MK will turn on (the red LED flashes briefly once every 3 seconds)

Note : Helpy 2W-V 12V MK is factory programmed for normally closed car- top and car-bottom pushbuttons (4110).

KCEAPM INSTALLATION

  • Open the Maintenance Access Panel (MAP), integrated in a landing door or wall-mounted, to gain access to the KCEAPM.

  • Disconnect the XM31 (signals) and X1 (telephone line) cables from the KCEAPM. KCEAPM will turn off.esse-ti 5HK-300 Kone Retrofit Kit fig \(15\)

  • Cut the yellow wire of the 5KT-120 retrofit kit cable (wire connected to pin n° 8 of the male Molex connector).

  • Open the Car Operating Panel (COP).

  • Lower the cable of the retrofit kit (5KT-120) from the car top.

  • Disconnect the 14-way cable from the J2 connector.

  • Connect the 14-way cable to the corresponding cable of the retrofit kit (5KT-120).

  • Connect the other end of the retrofit kit cable to the J2 connector.

  • Install Helpy 2W-V 12V MK on the top of the car.
    Please make sure the microphone is placed in correspondence with a car hole and the audio quality is good.

  • In any case Helpy 2W-V 12V MK can be installed facing upwards.

  • Helpy 2W-V 12V MK si accende (il LED rosso lampeggia una volta ogni 3 secondi).

Connecting the telephone line

  • Open the Base Unit Module installed at the top of the lift shaft.
  • Disconnect the telephone line from the Base Unit Module.
  • Disconnect the 4-way cable from the Base Unit Module.
  • Connect the 2 wires of the telephone line to any of the 2 wires in the 4-way cable
  • Disconnect from the LCEKNX KoneXion car interface (in the middle of the controller, in the lift shaft) the 4-way cable that comes from the Base Unit Module .
  • Disconnect the XC20 connector.
  • Connect the 2 wires of the 4-way cable used for the telephone line to the XC20 cable (trailing cable).
  • Open the Car Unit in Metal Box installed on the top of the car.
  • Disconnect the brown and blue wires from the Car Unit.
  • Connect the brown and blue wires to the LTI terminals of Helpy 2W-V 12V MK.

Connecting the pushbutton

  • Disconnect the white connector XB18 (10-way cable) from the box installed on the top of the car.
  • Cut the wire marked with number 5.
  • Connect both ends of wire 5 to a side of a 12 V relay coil.
  • Connect the other side of the relay coil to earth/ground.
  • Reconnect the connector XB18
  • Connect the normally open contacts of the relay to AL1 and — terminals of Helpy 2W-V 12V MK.
  • Connect the diode between +12 and C terminals.

Note : for basic programming see the table

BASIC PROGRAMMING

Access to programming *0#
1 st telephone number for emergency call 210112 < _telephone number

_ #
2 nd telephone number for emergency call| 210212 < telephone number #
3 rd telephone number for emergency call| 210312 < telephone number #
telephone number for periodic test call (CLI mode)| 210434 < telephone number > #
Record identification message| 7101 <registrare/ record >
Listen to identification message| 7201 < listen >
Emergency call button delay| 42X (X=3-9 seconds )
Emergency input AL1 normally closed/open| 4100 normally closed

Exiting the programming| *0#

Documents / Resources

| esse-ti 5HK-300 Kone Retrofit Kit [pdf] Instruction Manual
5HK-300, Kone Retrofit Kit, 5HK-300 Kone Retrofit Kit, Retrofit Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals