PowerA CPAC0235-01 RGB LED Light Strip User Manual

RGB LED LIGHT STRIP
BANDE LUMENEUSE DEL RGB USER MANUAL

INLINE CONTROL BOX

IR REMOTE

RGB LED STRIP SETUP

1. Peel back blue tape adhesive backing.

2. Press the LED strip firmly against surface when applying to ensure the tape adhesive sets.
   NOTE: Any dust or dirt should be wiped clean off desired surface before applying for best hold.
   

3. Connect the included AC power adapter to the inline control box. The power cable is the single cable coming out of the side of the control box with the Mode Selection button.

4. Connect the 4-pin connector-end of the LED strip to the inline control box. The LED connection cable is on the same side of the inline control box as the IR sensor cable and the Power button.
   A. NOTE: If the LED lights do not turn on when connected to power, press the Power button on the inline control box. Also check that the 4-pin connector is correctly oriented with the inline control box cable end: All 4 pins must line up with the holes in the inline cable end. If the lights do not turn on, unplug the LED strip from the inline cable, flip the light strip connector end and reconnect to the inline cable.
   

The IR sensor must be visible from wherever the controller will be used to control the LED strip. The
IR remote must be pointed at the IR sensor to control the LED strip.
INLINE CONTROL FEATURES

1. MODE SELECTION
   Each press of this button will change the LED mode on the strip:
   A. SOLID – All lights will be steadily lit with a single color. No speed settings for this mode.
   B. BREATHING – LED lights will slowly flash; pressing the View button will change speed.
   C. CYCLE – LED lights will cycle through all 24 available LED colors; pressing the VIEW button will change speed.
   D. MUSIC SOLID – LED lights will turn on with each noise or sound played; LED colors will change with each sound as well.
   E. MUSIC CYCLE – LED lights will flash in different colors each time a noise or sound is played.

2. COLOR SELECTION
   Each press of this button will cycle through 24 different LED colors.

3. POWER ON/OFF
   This will turn on or off the LED strip lights.

IR REMOTE FEATURES
ON: This button will turn ON the LED strip lights.
OFF: This button will turn OFF the LED strip lights.
R: Press to quick change ALL LED strip colors to the base RED color.
G: Press to quick change ALL LED strip colors to the base GREEN color.
B: Press to quick change ALL LED strip colors to the base BLUE color.
W: Press to quick change ALL LED strip colors to the base WHITE color.
COLOR CYCLE: Each press will change the LED strip colors to one of the 24 possible colors.
MODE SELECTION: Each press of this button will change the LED mode on the strip:
a. Solid b. Breathing c. Cycle d. Music Solid e. Music Cycle
+ : Pressing the plus button will increase the speed at which the mode behaves.
– : Pressing the minus button will decrease the speed at which the mode behaves.

WARNING

• INGESTION HAZARD: This product contains a coin battery.
• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
• KEEP new and used batteries OUT OF REACH OF CHILDREN.
• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

SAFETY GUIDANCE FOR COIN BATTERIES

• Battery type CR2025
• Nominal voltage DC3V
• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
• Remove and immediately discard batteries from equipment not used for an extended period of time
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble heat above (manufacturer’s specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
• Immediately dispose of used batteries and keep away from children. Do NOT dispose of batteries in household trash.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.

SETUP:
ADVANTAGE WIRED CONTROLLER FOR XBOX SERIES X|S WITH LUMECTRA
The following instructions describe how to control LED light strip settings wirelessly with the Advantage Wired Controller for Xbox Series X|S with Lumectra. (sold separately).

• Connect the 10 ft. USB cable by plugging it into any available USB port on your Xbox console.
• Connect the other end to the USB-C port on your PowerA Advantage Wired Controller for Xbox Series X|S with Lumectra.
• Hold down the Xbox Button until your console powers “ON”. The controller’s Connection / Program LED will illuminate to indicate your controller is connected.

INTERNAL LEDS – PROGRAM FUNCTION
The controller has 4 separate lighted Lumectra Zones that you can customize:

1. To enter LED Program Mode on the controller, hold the INT LED button on the back of the controller for 2 seconds.
   The Program / Connection LED will blink slowly while the controller is in LED Program Mode.

2. The current programmable Zone will flash 3 times. To toggle through the 4 Zones, press “Right” on the D-Pad. (Zone One is the default starting zone.)

3. Select one of the A/B/X/Y buttons to choose your color: green, red, blue, or yellow.

4. Next, continue pressing the selected A/B/X/Y button to toggle through 6 shades of that color.

5. Press “Left” on the D-Pad to program the zone’s light effect: “Solid”, “Breathing”, or “Cycle”.

6. Press “UP” and “DOWN” on the D-Pad to adjust that zone’s brightness level.

7. In program mode, press “INT LED” once to turn off the current zone independently of the other zones. If the current zone is set to “off”, press “INT LED” once to turn the zone back on. NOTE: Outside of program mode, pressing  “INT LED” once will turn all LEDs on or off.

8. Press the “View” button to toggle through multiple speed settings for the current zone. Press the Menu button to toggle through multiple speed settings for all 4 zones simultaneously.
   NOTE: This feature is only available in “Breathing” and “Cycle” modes.

9. While in program mode, press LB to sync all zones to the same lighting mode and toggle all zones through the 3 lighting modes simultaneously; press RB to sync all zones to the same color and toggle all zones through the 24 colors  and shades simultaneously. .

10. While in program mode, press LT to decrease the brightness of all zones simultaneously; press RT to increase the brightness of all zones simultaneously.

11. While in program mode, hold “INT LED” for 2 seconds to save any changes made to light settings.
    All 4 LED zones will flash 3 times to indicate the controller is now out of LED program mode. NOTE: The controller will store the 2 most recently saved LED light settings.

12. Outside program mode, double press “INT LED” quickly to toggle between the 2 most recently saved light settings.

13. Outside program mode, press “INT LED” once to turn all LEDs on or off. The LEDs will display the most recently used selection of saved settings.

EXTERNAL LEDS – PROGRAM FUNCTION

1. To enter EXTERNAL LED Program Mode on the controller, hold the EXT LED button on the back of the controller for 2 seconds. The Program/Connection LED will blink slowly while the controller is in EXTERNAL LED Program  Mode.
   

2. The LED strip will flash 3 times in GREEN color to indicate you are in EXTERNAL LED program mode and are ready to change LED colors using the controller. The controller will also continuously flash GREEN while in  EXTERNAL LED program mode.
   NOTE: While in EXTERNAL LED program mode, your controls to the console will not function. This is to allow you to press buttons without causing any movement or actions on the game or console dashboard. The controller  sends commands to the LED strip via the IR sensor on the LED strip. You must point the controller directly at the sensor (line of sight) to enable the EXTERNAL commands to register and take effect on the LED strip.

3. COLOR SELECTION
   Select one of the A/B/X/Y buttons to choose your color: green, red, blue, or yellow.
   A. Next, continue pressing the selected A/B/X/Y button to toggle through 6 shades of that color.
   B. Pressing and holding down any of the A/B/X/Y  buttons will cycle through the 6 shades of that color until the button is released.

4. MODE SELECTION
   Press the D-Pad Left to cycle through the LED modes on the strip:
   A. SOLID – All lights will be steadily lit with a single color. No speed settings for this mode.
   B. BREATHING – LED lights will slowly flash; pressing the VIEW button will change speed.
   C. CYCLE – LED lights will cycle through all 24 available LED colors; pressing the VIEW button will change speed.
   D. MUSIC SOLID – LED lights will turn on with each noise or sound played; LED colors will change with each sound as well.
   E. MUSIC CYCLE – LED lights will flash in different colors each time a noise or sound is played.

5. BRIGHTNESS ADJUSTMENT
   Press “UP” or “DOWN” on the D-Pad to adjust brightness levels. There are 10 available brightness settings.

6. SYNC
   The External LED strip can be synced to one of the 4 Lumectra LED zones on the controller. Press the RB button on the controller to cycle through each zone. The zone being synced with the LED strip will flash, and the LED strip  will display that zone’s color.

7. EXIT EXTERNAL LED PROGRAM MODE
   To exit Program Mode, hold the EXT LED button for 2 seconds. All 4 LED Controller Zones and LED Strip will flash 3 times to indicate the LED strip is now out of LED Program Mode.

8. LED STRIP ON/OFF
   Outside Program Mode, press EXT LED once to turn the LED strip on or off.

INT/EXT LED BUTTON MAPPING: FRONT

INT/EXT LED BUTTON MAPPING: BACK

TROUBLESHOOTING

For latest FAQs, visit PowerA.com/Support.
Q: Controller will not connect to Xbox console?
A: Confirm your Xbox console is powered “ON”.
A: Confirm your TV is set to the proper Video Input and that you can see the Xbox console interface on your TV screen.
A: Confirm cable is properly connected to your Xbox console.
A: Confirm cable is properly connected to your PowerA Wired Controller.
Q: Controller is connected but has no function?
A: Confirm you are using the Player #1 controller. For more troubleshooting refer to your Xbox console User Manual.
Q: LED strip will not turn on?
A: Make sure you have plugged in the USB cable to a powered source.
A: Press the “ON/OFF” button on the inline control box.
Q: The External LED strip will not change colors?
A: Make sure there is power to the unit, and that it is turned “ON”.
A: Enable EXT LED programming mode by pressing and holding the EXT LED button on the back of the controller until both the controller LEDs and LED strip lights flash GREEN.
Q: Music mode is not reacting?
A: Make sure the volume is loud enough on your TV or speaker.
A: Enable one of the Music modes by pressing the MODE button on the inline control box, or by pressing D-Pad LEFT on the controller while in EXT LED program mode.
Q: One of the LED zones will not illuminate.
A: When in INT LED program mode press the INT LED button once to turn ON/OFF the selected zone.
Also make sure you have not turned down the brightness in the selected zone.
WARNING: READ BEFORE PLAYING
A very small percentage of individuals may experience epileptic seizures when exposed to certain light patterns or flashing lights. Exposure to certain patterns or while playing video games, may induce an epileptic seizure in these  individuals. Certain conditions may induce previously undetected epileptic symptoms even in persons who have no history for prior seizures of epilepsy. If you, or anyone in your family, have an epileptic condition, consult
your physician prior to playing. If you experience any of the following symptoms while playing a video game – dizziness, altered vision, eye or muscle twitches, loss of awareness, disorientation, any involuntary movement, or convulsions  – IMMEDIATELY discontinue use and consult with your physician before resuming play.
MOTION WARNING
Playing video games can make your muscles, joints, skin or eyes hurt. Follow these instructions to avoid problems such as tendinitis, carpal tunnel syndrome, skin irritation or eyestrain:

• Avoid excessive play. Take a 10- to 15-minute break every hour, even if you don’t think you need it.
  Parents should monitor their children for appropriate play.

• If your hands, wrists, arms or eyes become tired or sore while playing, or if you feel symptoms such as tingling, numbness, burning or stiffness, stop and rest for several hours before playing again.

• If you continue to have any of the above symptoms or other discomfort during or after play, stop playing and see a doctor.

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference  that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules.
CAN ICES-003(B)/NMB-003(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

MANUFACTURED FOR
ACCO Brands USA LLC, 4 Corporate Drive, Lake Zurich, IL 60047
ACCOBRANDS.com | POWERA.com | MADE IN CHINA
CONTACT/SUPPORT
For support with your authentic PowerA accessories, please visit PowerA.com/Support.
WARRANTY
2-Year Limited Warranty: Visit PowerA.com/Support for details.
WARRANTY AGAINST DEFECTS, AUSTRALIA & NEW ZEALAND CUSTOMERS
This product is provided with a 2-year warranty against defects in manufacturing or materials from the date of purchase. ACCO Brands will either repair or replace a faulty or defective product subject to the conditions of this warranty.  Claims under this warranty must be made to the place of purchase within the warranty period with proof of purchase by the original purchaser only. Expenses associated with a warranty claim are the responsibility of the consumer.  Conditions of this warranty are on our website:
PowerA.com/warranty-ANZ
This warranty is provided in addition to other rights or remedies available to you under the law. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major  failure.
DISTRIBUTOR CONTACT DETAILS
AUSTRALIAN CUSTOMERS:
ACCO Brands Australia Pty Ltd
Locked Bag 50, Blacktown BC, NSW 2148
Phone: 1300 278 546 | Email: consumer.support@powera.com
NEW ZEALAND CUSTOMERS:
ACCO Brands New Zealand Limited
PO Box 11-677, Ellerslie, Auckland 1542
Phone: 0800 800 526 | Email: consumer.support@powera.com

ADDITIONAL LEGAL
© 2023 ACCO Brands. All Rights Reserved. Lumectra, PowerA and PowerA Logo are trademarks of ACCO Brands.
REGIONAL COMPLIANCE SYMBOLS
More information available via web-search of each symbol name.

Waste Electrical and Electronic Equipment (WEEE): Electrical and electronic devices and batteries contain materials and substances that can have damaging effects on human health and the environment. This symbol indicates that this device and the battery must not be treated as household waste and must be collected separately. Dispose of the device via a collection point for the recycling of waste electrical and electronic equipment within the EU, UK and in other  European countries that operate separate collection systems for waste electrical and electronic equipment and batteries. By disposing of the device and the battery in the proper manner, you help to avoid possible hazards for the  environment and public health that could otherwise be caused by improper treatment of waste equipment. The recycling of materials contributes to the conservation of natural resources.
The CE (Conformité Européene aka European Conformity) mark is a declaration from the manufacturer that the product meets applicable European Directives and Regulations for health, safety, and environmental protection.
****The UKCA (UK Conformity Assessment) mark is a declaration from the manufacturer that the product meets applicable UK Regulations for health, safety, and environmental protection.
The Regulatory Compliance Mark is a visible indication of a product’s compliance with all applicable ACMA (Australian Communications and Media Authority) regulatory arrangements, including all technical and record-keeping requirements regarding the electrical safety and/or electromagnetic compatibility (EMC).

References

• ACCO Brands
• PowerA | PowerA
• Support | PowerA
• Warranty-ANZ | PowerA
• gesetzeim-internet.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>