Voagupa XY-02A Ptc Tower Space Heater User Manual

Voagupa XY-02A Ptc Tower Space Heater

Thanks for choosing the QTREE PTC Tower Space Heater with Digital Fireplace. Please read this User Manual thoroughly before use and retain it for future reference.

PACKAGE INCLUDED

• 1 x PTC Tower space heater with digital fireplace
• 1 x Remote control
• 1 x User Manual

HOW TO USE

BASE ASSEMBLED AND SEPARATED
ASSEMBLED: Align and combine the 4 buckles on the base with the four holes on the bottom of the space heater.
SEPARATED: Please inward press the four buckles at the base and pull out.

IMPORTANT
To avoid power cord damage. Please make sure the cord slot at the base is aligned with the power cord outlet hole before assembly.

CONTROL PANEL

CHANGING THE BATTERY

1. Push the replace button inwards and pull the battery casing out. Remove the old battery.
2. Insert 1x CR2025 battery into the battery casing ensuring you follow the polarity ( + and -) marked on the casing.
3. Slide the battery casing back into the remote control thoroughly before reassembling the appliance.
4. Don’t use solvents, chemical or abrasive cleaning agents, wire brushes, sharp objects or scouring pads to clean the appliance.
5. Always clean the appliance before storing it for a long time.
6. Never immerse the appliance in water.
7. When an appliance is not in use for a long period, store the appliance in its original packaging or a dust-free and dry environment.

IMPORTANT
When using this tower space heater, basic safety precautions should always be followed to reduce injury to persons, and the risk of fire and electric shock, including the following:

1. Read the instructions clearly before using this unit.
2. DO NOT touch the control panel or plug with a wet hand.
3. DO NOT run the cord under the carpeting.
4. DO NOT cover the cord with throw rugs, runners, or similar coverings. Arrange the cord away from traffic areas and where it will not be tripped over.
5. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
6. DO NOT operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
7. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user-serviceable parts. Qualified personnel should perform all servicing only.
8. CAUTION: Risk of Electric Shock. Don’t open or try to repair the heater yourself.
9. This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Do not place it against walls, furniture, curtains, etc.
10. Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 ft from the front of the heater and keep them away from the sides, top, and rear. DO NOT place towels or other objects on the heater.
11. Extreme caution is necessary when any heater is used by or near children or the disabled, or when the heater is left operating and unattended.
12. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate a heater where it may fall into a bathtub or other water container. To protect against electrical hazards, Don’t immerse in water or other liquids.
13. To prevent a possible fire, Don’t block the air intake or exhaust in any manner. Don’t use it on soft surfaces, like a bed, where openings may become blocked.
14. A heater has hot and arcing or sparking parts inside. Don’t use it in areas where gasoline, paint, explosive and/or flammable liquids are used or stored. Keep the unit away from heated surfaces and open flames.
15. Always plug heaters directly into a wall outlet receptacle. Never use an extension cord or relocatable power tap (outlet/power strip).
16. To avoid fire or shock hazards, plug the unit directly into a 120 V AC electrical outlet.
17. To disconnect the heater, turn the controls OFF, then remove the plug from the outlet. Pull firmly on the plug, DO NOT unplug by pulling on the cord.
18. Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
19. Always use on a dry, level surface. Use on the floor only.
20. WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control device.

OVERVIEW

1. Control Panel
2. LED Display
3. Air Outlet
4. Digital Fireplace
5. Handle
6. Air Inlet
7. Base

APPLIANCE FEATHER

• Touch control panel
• 8 hours timer
• Infrared remote control
• Intelligent temperature control
• Automatically pause the screen
• Shaking head function
• Tip Protection (when the product tips over 30° the product will automatically power off to confirm the safety.

PTC WORKING INSTRUCTION

Constant temperature mode: When the temperature reaches the set temperature, the PTC stops generating heat, and the wind wheel continues to operate using natural wind for 10 seconds and then stops working. When the temperature drops by 2°F, the PTC and wind wheel start operating simultaneously. When the temperature drops by 4°F from the set temperature, the power will be converted from 750W to 1500W to raise the temperature to the set temperature.

PTC WORKING INSTRUCTION

1. Please make sure the power plug has been unplugged and let it cool down before cleaning.
2. Wipe the outside of the space heater and remote control gently. damp and dry thoroughly. Don’t let any liquid enter the heater or the remote control.
3. Remove the air inlet filter by lifting the tabs at the bottom of the filter and pulling it away from the appliance. Clean under running water

LED DISPLAY

REMOTE CONTROL

POWER PARAMETERS

• Model No.: XY-02A
• Rated Power: 1500W
• Rated Voltage: 110V
• Rated Frequency: 60Hz

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>