PowerA 1510925 Spectra Enhanced Wired Controller for Nintendo Switch Black LED User Manual
- June 3, 2024
- PowerA
Table of Contents
1510925 Spectra Enhanced Wired
Controller for Nintendo Switch Black LED
**User Manual
**
1510925 Spectra Enhanced Wired Controller for Nintendo Switch Black LED
|
---|---
CONTENTS
- Spectra Enhanced Wired Controller for Nintendo Switch™
- Detachable 10ft (3m) USB Cable
- User Manual
SET UP
1. Make sure your Nintendo Switch system is powered on and connected to your
TV.
2. Insert the USB cable into a USB port on the Nintendo Switch dock. Connect
the other end of the cable to the wired controller. Your wired controller is
now ready for use.
BASIC USAGE
You can connect multiple wired controllers to the Nintendo Switch console at a time. On-screen notifications will indicate which USB channel each controller is connected to.
ASSIGNING ADVANCED GAMING BUTTONS
- Press and hold the Program Button on the back of the controller for 2-3 seconds. The Program LED Indicator will flash, signaling the controller is in Assign Mode.
- Press 1 of the following buttons (A/B/X/ Y/L/R/ZL/ZR/Left Stick Press/Right Stick Press/+Control Pad) to re-assign. Then press the Advanced Gaming Button (AGR or AGL) that you wish to assign. The Program LED Indicator will stop flashing, signaling the Advanced Gaming Button has been set.
- Repeat for the remaining Advanced Gaming Button.
NOTE : Advanced Gaming Button assignments will remain in memory even after being disconnected.
RESETTING ADVANCED GAMING BUTTONS
1. Hold the Program Button down for 2-3 seconds.
The Program LED Indicator will slowly flash, signaling the controller is in
program mode.
2. Press and hold the Program Button for 5 seconds to reset to no function.
ILLUMINATION
1. Press the Color Cycle Button on the back of the controller to select your
LED setting.
2. Continue pressing the Color Cycle Button to toggle through the 8 LED
colors, then Rainbow Phase, and then off.
3. Press and hold the Color Cycle Button for 3 seconds to turn the LEDs off.
TROUBLESHOOTING
Q1. Why isn’t my controller connecting to my Nintendo Switch console?
– A1. Confirm that the USB Cable is securely connected to the wired controller
and the Nintendo Switch dock.
– A2. Confirm that the Nintendo Switch is powered on and connected to an
external display before connecting your wired controller.
– A3. Confirm that your Nintendo Switch has the latest System Update
installed.
Q2. Why don’t I feel any vibration when using this controller?
– A1. This product does not support vibration functionality
WARNING: READ BEFORE PLAYING
A very small percentage of individuals may experience epileptic seizures when
exposed to certain light patterns or flashing lights. Exposure to certain
patterns or while playing video games may induce an epileptic seizure in these
individuals.
Certain conditions may induce previously undetected epileptic symptoms even in
persons who have no history of prior seizures of epilepsy.
If you, or anyone in your family, have an epileptic condition, consult your
physician prior to playing.
If you experience any of the following symptoms while playing a video game –
dizziness, altered vision, eye or muscle twitches, loss of awareness,
disorientation, any involuntary movement, or convulsions – IMMEDIATELY
discontinue use and consult with your physician before resuming play.
MOTION WARNING
Playing video games can make your muscles, joints, skin, or eyes hurt. Follow these instructions to avoid problems such as tendinitis, carpal tunnel syndrome, skin irritation or eyestrain:
- Avoid excessive play. Take a 10 to 15-minute break every hour, even if you don’t think you need it. Parents should monitor their children for appropriate play.
- If your hands, wrists, arms, or eyes become tired or sore while playing, or if you feel symptoms such as tingling, numbness, burning or stiffness, stop and rest for several hours before playing again.
- If you continue to have any of the above symptoms or other discomforts during or after play, stop playing and see a doctor.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
WARNING : Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits
for Class B digital devices, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAN ICES-003(B)/NMB-003(B)
This device contains license-exempt transmitter(s)/ receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference;
- This device must accept any interference, including interference that may cause undesired operation of the device
MANUFACTURED BY
ACCO Brands USA LLC,
4 Corporate Way, Lake Zurich, IL 60047
ACCOBRANDS.com | POWERA.com
MADE IN CHINA
CONTACT/SUPPORT
For support with your authentic PowerA accessories, please visit
PowerA.com/Support.
WARRANTY
2-Year Limited Warranty: Visit PowerA.com/support
for details.
AUSTRALIAN WARRANTY STATEMENT
This product comes with guarantees that cannot be excluded under the
Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure. If
purchased within Australia or New Zealand, this product comes with a one-year
warranty from the date of purchase.
Defects in the product must have appeared within one year from the date of
purchase, in order to claim the warranty. All warranty claims must be
facilitated back through the retailer of purchase in accordance with the
retailer’s return policies and procedures.
Any expenses incurred, as a result of returning the product to the retailer of
purchase are the full responsibility of the consumer.
TWO-YEAR LIMITED WARRANTY
For warranty details or support with your authentic PowerA accessories, please visit PowerA.com/Support.
AU WHOLESALE DISTRIBUTOR
Level 2, 2 Darling Street South Yarra, Australia VIC 3141 |
bluemouth.com.au
Email: support@bluemouth.com.au
+61 (3) 9867 2666
ADDITIONAL LEGAL
© 2021 ACCO Brands USA LLC. PowerA and PowerA Logo are trademarks of ACCO
Brands Corporation.
Nintendo Switch is a trademark of Nintendo. Licensed by Nintendo. All rights
reserved. All other trademarks are the property of their respective owners.
REGIONAL COMPLIANCE SYMBOLS
More information available via web-search of each symbol name.
The WEEE (Waste of electrical and electronic equipment) symbol requires
battery disposal outside of other household waste per local regulations.
Contact your city office, waste disposal service, or retailer for guidance.
The CE (Conformité Européene aka European Conformity) mark is a
declaration from the manufacturer that the product meets applicable European
Directives and Regulations for health, safety, and environmental protection.
The UKCA (UK Conformity Assessment) mark is a declaration from the
manufacturer that the product meets applicable UK Regulations for health,
safety, and environmental protection.
The Regulatory Compliance Mark is a visible indication of a product’s
compliance with all applicable ACMA (Australian Communications and Media
Authority) regulatory arrangements, including all technical and record-keeping
requirements regarding the electrical safety and/or electromagnetic
compatibility (EMC).
DECLARATION OF CONFORMITY
Hereby, ACCO Brands USA LLC at 4 Corporate Way, Lake Zurich, IL 60047 USA,
declares that this wired controller is in compliance with Directive 2014/30/
EU. The full text of the EU Declaration of Conformity is available at the
following internet address:
PowerA.com/compliance
References
- ACCO Brands
- bluemouth.com.au
- PowerA | PowerA
- PowerA | PowerA
- Declaration of Conformity | PowerA
- Support | PowerA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>