REZNOR EBHB Electric Baseboard Heater Instructions
- June 4, 2024
- Reznor
Table of Contents
EBHB Electric Baseboard
Heater Instructions
EBHB Electric Baseboard Heater
THE INSTALLATION MUST BE EXECUTED BY A QUALIFIED TECHNICIAN.
RISK OF ELECTROCUTION
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be taken to reduce the risk of fire, electric shock, and injury, including the following: Read all instructions before using this heater.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, like furniture, pillows, bedding, papers, clothes, and curtains away from the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any way whatsoever.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- Do not install a heater against combustible low-density cellulose fiberboard surfaces.
- Do not use outdoors.
- WARNING – High Temperature; Keep electrical cords, drapes, and other furnishings away from the heater.
- Use only copper branch circuit conductors.
- For bathroom use, the heater must be installed so that switches and other controls cannot be touched by anyone in the bath or shower.
- Do not install this heating appliance beneath a wall outlet.
- To avoid possible electrical shock, disconnect all power at the main panel prior to wiring, cleaning, or servicing.
- If the product is damaged or has missing parts (e.g., dents, damaged or missing element fins), stop using the device immediately and replace it.
- KEEP THESE INSTRUCTIONS.
FURNITURE AND DRAPES
For maximum satisfaction, an airflow of 3 in. (76.2 mm) clearance is
recommended. Also, allow 1 in. (25.4 mm) clearance on top and bottom of drapes
when drapes cover the wall.
INSTALLATION INSTRUCTIONS
- Remove the wire holder (or knock-out) of the appropriate junction box.
- Make connections according to local and national codes and replace the wire holders. (Do not forget ground wire.)
- Install the relay or thermostat by removing the front panel and the junction box cover.
- Check the wire connection at the other junction box. 5- Fasten the baseboard to the wall using wood screws, tighten then release 1/2 turn. 6- Replace all covers before energizing.
INTERCONNECTION
The connection boxes and wiring channel are approved for interconnection of
baseboard heaters and components which are on the same heating branch circuit.
Use a ‘‘BX’’ cable to run wiring for all other options in this series. (Ex:
Corner box, empty cabinets, etc.).The heater junction box minimum volume
without options is 31.2 in³ (512 cm³).
CORNERS AND BLANK SECTIONS
Install blank sections and corners the same way as a heating unit of this series. Use ‘‘BX’’cable to run wiring into these options.
OPTIONS
All heating equipment and options must be installed in accordance with local
and national codes.
Built-in thermostat:
CAUTION: The thermostat should not be considered as an infallible system
were maintaining a temperature is considered critical. Examples: Hazardous
material storage, computer room, etc. In these particular cases, it is
imperative to add a monitoring system to avoid the consequences of a failure
of the thermostat.
– Refer to the wiring diagram for connections.
– Refer to the instructions supplied with the option for mounting. Built-in
relay:
– Refer to the diagram included with the relay option for connections.
– Refer to the instructions supplied with the option for mounting.
MAINTENANCE
– Once a year or at the need, remove the front panel and use a vacuum cleaner
to remove the dust accumulation inside the heater.
– Cleaning should be done while the heater is disconnected from the main
service panel. Wait until the housing and heating element cool before
performing maintenance. Remove the front panel.
CAUTION: Fins on the element are sharp
– Do not touch. Replace all covers before energizing.
– Any other servicing should be performed by a qualified technician.
Reznor LLC
O’Fallon, MO USA 63368
Tel.: 1 800 695-1901
www.ReznorHVAC.com
©2022 Reznor, LLC. All rights reserved. All other trademarks are
the property of their respective organizations.
INS338-201204-02
Documents / Resources
|
REZNOR EBHB Electric Baseboard
Heater
[pdf] Instructions
EBHB Electric Baseboard Heater, EBHB, Electric Baseboard Heater, Baseboard
Heater, Heater
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>