RetroSound 068REDM1BS Redondo RS M2B Digital Media Receiver For Select Chrysler And Ford Vehicles User Guide

RetroSound 068REDM1BS Redondo RS M2B Digital Media Receiver For Select

Chrysler And Ford Vehicles

Product Information

• Control Shaft x 10
• Hardware x 2
• InfiniMount Brackets x 2
• Control Shaft Quick Start Guide x 1
• Installation Manual x 1

Included in your Radio Motor box|

• Shaft Nut x 8
• Shaft Washer x 8
• Optional hardware x 10

What’s in the Box

Control Shaft

Hardware

Installation

• Attach each InfiniMount Bracket to the Radio Motor with the eight small screws.
• Place a Shaft Nut and Shaft Washer onto each Control Shaft before inserting them into the InfiniMount Brackets. The Control Shaft depth and height can be adjusted as needed.
• To complete the installation secure each Control Shaft with a Shaft Nut and Shaft Washer then plug each shaft into the side of the Radio Motor. Use the optional hardware if needed to help mount the radio to the dash.

Control Layout

Radio Presets

• Setting Radio Presets
  To set a preset, tune to the station you want to set the preset to, and then press and hold the desired Preset Button(5) for two seconds.

• Recalling Radio Presets
  To recall a preset, simply press the Preset Button(5) your station was set to previously.

Basic Operation

• Power On/Off

  • Press the Left-Front Knob(1) to power the unit on.
  • Press and hold the Left-Front Knob(1) to power the unit off.

• Volume
  Rotate the Left-Front Knob(1) to change the volume.

• Changing Source Modes
  Rotate the Left-Rear Knob(2) clockwise to cycle through the source modes.

• Changing Radio Bands
  Rotate the Right-Rear Knob(4) counter-clockwise to cycle through the radio bands.

• Tune
  Rotate the Right-Front Knob(3) to scroll through the stations.

• Mute On/Off
  Press the Right-Front Knob(3) to mute and unmute.

• Equalizer (EQ)

  • Press the Left-Front Knob(1) to enter the Tone Control sub-menu.
  • Press and release the Left- Front Knob(1) until you see the EQ setting you’d like to adjust.
  • Rotate the Left-Front Knob(1) to adjust the setting.
  • Press the Left-Front Knob(1) to move to the next item, and repeat to adjust each option. Let the unit time out to set.

• Setting the Clock

  • Press and hold the Right-Front Knob(3) to enter the System Settings sub-menu. Rotate the
  • Right-Front Knob(3) to cycle through the choices until you see CLK, then press the Right-
  • Front Knob(3) to select. Rotate the Right-Front Knob(3) to adjust the hours. Then press the
  • Right-Front Knob(3) again to move on to minutes. Rotate the Right-Front Knob(3) to adjust the minutes. Let the unit time out to set.

• **Display Color***

  • Press and hold the Right-Front Knob(3) to enter the System Settings sub-menu. Rotate the
  • Right-Front Knob(3) to cycle through the choices until you see SCAN, then press the Right
  • Front Knob(3) to cycle through the colors. Let the unit time out to set.

• Beep On/Off

  • Press and hold the Right-Front Knob(3) to enter the System Settings sub-menu. Rotate the
  • Right-Front Knob(3) to cycle through the choices until you see BEEP ON/OFF, then press the
  • Right-Front Knob(3) to choose between BEEP ON or BEEP OFF. Let the unit time out to set.

[email protected]
help.retromanufacturing.com

References

• Retro Manufacturing Knowledge Base

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>