LEVITON IP66 PIR Integrated Fixture Mount Sensors User Guide
- June 13, 2024
- Leviton
Table of Contents
LEVITON IP66 PIR Integrated Fixture Mount Sensors
Smart Integrated Fixture Mount Sensors
- Fixture Mount Sensors are shipped ready to operate in the following default mode:
- Auto-ON
- 20-minute timeout
- Daylight Harvesting
- No adjustments or app required to operate in this mode
- Sensors will automatically start daylight calibration and remain ON for 24 hours
- Sensors will be fully calibrated after 24 hours and begin operating in default mode
Smart Sensor App Overview
- Easy-to-use
- Intuitive
- Advanced occupancy and daylighting options
- Templates
- Options for grouping & scheduling
- Over-the-Air (OTA) updates allows for new features, easy updates
Download Smart Sensor App
-
Download the Leviton Smart Sensor App from Google Play Store or Apple App Store on a phone or tablet
-
Connects to sensor via Bluetooth
-
Sensor default settings:
-
Auto-ON, 20-min timeout, Daylight Harvesting
-
No configuration needed if using these settings
-
Smart Sensor App required for any changes to product configuration
-
App is used for several Smart Sensor products
- Need to select Fixture Mount Sensor
-
(?) Provides contextual help
-
Helpful hints
-
Available on each page in app
-
No need to put sensors in pairing mode; always available to connect using App
Product Configuration – Notes
For first time connections (if prompted):
- Click OKAY for Bluetooth Access
- Allow Leviton Smart Sensor to access device location, either “While using the app” or “Only this time”
Firmware Updates
- Check “More Details” on main settings page to see current Model / Firmware details and whether any updates are available
- Clicking “Update Available” will update sensor to latest firmware level
- Updates take 1-2 mins
- Note : updates not required unless needed for latest feature set
| Firmware Level | Features | Notes |
|---|---|---|
| 1.0 | Initial Release | |
| 1.3 | Grouping/ Misc Updates | Allows for grouping up to 16 sensors; misc. |
updates
1.4| Scheduling| For OFDUZ and ZLUDZ models only
- Most inventory currently at 1.3
- If UPDATE AVAILABLE shows, updating firmware will update to latest level (1.4)
- Note : Updates not required unless needed for latest feature set
Product Programming
Product Configuration
Scanning: Helpful Hints
Sensor Configuration – Main Settings Page
Sensor Configuration – Advanced Settings
Advanced Settings – Daylighting Options
Advanced Settings – Dimming & Load
Advanced Settings – Templates
Sensor Grouping
Grouping Overview
- Fixtures / Sensors to be wired and installed per installation instructions
- Up to 16 sensors can be grouped together
- Sensors are grouped together via BLE network
- Distance (end-to-end) is limited by Bluetooth signal range
- For best results:
- Determine how you want your sensors grouped (ex: per aisle or space)
- Grouping is done from the initial scan page
- Select a sensor in middle of group as the “pro visioner”, and add other sensors to the group from this sensor
Creating a Group
Adding Additional Sensors to a Pre-Existing Group
Removing a Group
Scheduling
Scheduling Overview
- Scheduling allows sensors to behave differently based on the time of day or day of the week to maximize energy savings
- Ability to change light level, operating mode, timeout, partial-ON & OFF, and daylight mode
- Scheduling can be done individually or shared across a group
- Only universal voltage models (ZLDUZ and OFDUZ) have the scheduling feature
- Groups of mixed product including the non-universal voltage models (ZLD1Z and OFD1Z) can support scheduling if included with groups of ZLDUZ/OFDUZs
- Note : must be connected to the ZLDUZ/OFDUZ via the Smart Sensor App to initiate the schedule feature
Creating Schedules and Behaviors for a Group of Sensors
Operating mode options:
- Auto ON: Sensor automatically turns light ON with Occupancy, default is 100%; level can be adjusted
- Auto OFF: Sensor automatically turns light Lights turn off and OFF with Vacancy, default is 0%; level can be adjusted
- Photocell Only: Disables the occupancy sensor and lights ON and OFF and/or dims them UP or DOWN based on ambient lighting conditions only
Level: Devices will be held at the specified brightness level for the duration
of the schedule running this behavior
Timeout:
- Turns lights off to desired Auto Off level at desired time between 20 seconds and 60 minutes
- Not available in photocell only mode
Full Off Timeout:
- Secondary Timeout feature; turn light off fully at desired time between 20 seconds and 60 minutes
Creating Schedules and Behaviors for a Group of Sensors, Part 5
Thank You
Documents / Resources
|
LEVITON IP66 PIR Integrated Fixture Mount
Sensors
[pdf] User Guide
OFDUZ, ZLUDZ, OFDUZ Fixture Integrated Smart Sensor, Fixture Integrated Smart
Sensor, Integrated Smart Sensor, Smart Sensor, Sensor
---|---