MEAN WELL LPF-60D-12 Constant Current Mode LED Driver Owner’s Manual

: June 13, 2024
: MEAN WELL

MEAN WELL LPF-60D-12 Constant Current Mode LED Driver

MEAN WELL LPF-60D-12 Constant Current Mode LED Driver

Features

Constant Current mode output
Plastic housing with Class II design
Built-in active PFC function
Class 2 power unit
IP67 rating for indoor or outdoor installations
Function: 3 in 1 dimming
Typical lifetime>50000 hours
5 years warranty

Description

LPF-60D series is a 60W AC/DC LED driver featuring the constant current output. LPF-60D operates from 90~305VAC and offers models with different rated voltage ranging between 12V and 54V. Thanks to the high efficiency up to 90%, with the fanless design, the entire series is able to operate for -40 °C ~ +80°C case temperature under free air convection. The entire series is rated with IP67 ingress protection level and is suitable to work for a variety of applications at dry, damp or wet locations. LPF-60D is equipped with the 3 in 1 dimming function so as to provide the design flexibility for LED lighting system.

Model Encoding

Applications

LED panel lighting
LED downlight
LED decorative lighting
LED tunnel lighting
Moving sign

GTIN CODE

MW Search: https://www.meanwell.com/serviceGTIN.aspx

SPECIFICATION

MODEL| LPF-60D-12| LPF-60D-15| LPF-60D-20| LPF- 60D-24| LPF-60D-30| LPF-60D-36| LPF-60D-42| LPF-60D-48| LPF-60D-54
---|---|---|---|---|---|---|---|---|---
OUTPUT| DC VOLTAGE| 12V| 15V| 20V| 24V| 30V| 36V| 42V| 48V| 54V
RATED CURRENT| 5A| 4A| 3A| 2.5A| 2A| 1.67A| 1.43A| 1.25A| 1.12A
RATED POWER Note.5| 60W| 60W| 60W| 60W| 60W| 60.12W| 60.06W| 60W| 60.48W
CONSTANT CURRENT REGION Note.2| 7.2 ~12V| 9 – 15V| 12- 20V| 14.4 – 24V| 18- 30V| 21.6~36V| 25.2 ~ 42V| 28.8 – 48V| 32.4- 54V
CURRENT RIPPLE| 5.0% max. @rated current
CURRENT TOLERANCE| ±5.0%
SETUP, RISE TIME Note.6| 1000ms, 80ms / 115VAC 500ms, 80ms / 230VAC
HOLD UP TIME (Typ.)| 16ms/230VAC 16ms/115VAC
INPUT| VOLTAGE RANGE Note.5| 90 ~ 305VAC 127 – 431VDC (Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE| 47 – 63Hz
POWER FACTOR| PF >= 0.97/115VAC, PF >= 0.95/230VAC, PF >= 0.92/277VAC@full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
TOTAL HARMONIC DISTORTION| THD< 20%(@Ioad 60%/115VC,230VAC; @load 75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
EFFICIENCY (Typ.)| 86%| 87%| 88%| 89%| 90%| 90%| 90%| 90%| 90%
AC CURRENT| 0.8A/ 115VAC 0.4A / 230VAC 0.32A/277VAC
INRUSH CURRENT(Typ.)| COLD START 55A(twidth=270µs measured at 50% Ipeak) at 230VAC; Per NEMA410
MAX. No. of PSUs on 16A CIRCUIT BREAKER| 8 units (circuit breaker of type B) / 14 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT| <0.75mA / 240VAC
PROTECTION| OVER CURRENT| 95 -108%
Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT| Hiccup mode, recovers automatically after fault condition is removed.
OVER VOLTAGE| 15-17V| 17.5- 21V| 23 – 27V| 28- 35V| 34 ~ 40V| 41 -49V| 46 – 54V| 54- 63V| 59- 66V
Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE| Shut down o/p voltage, re-power on to recover
ENVIRONMENT| WORKING TEMP.| Tcase=-40 – +80″C (Please refer to” OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP.| Tcase=+80″C
WORKING HUMIDITY| 20 – 95% RH non-condensing
STORAGE TEMP. HUMIDITY| -40 ~ +80’C, 10-95% RH
TEMP. COEFFICIENT| ±0.03%/”C (0 – 50’C )
VIBRATION| 10- 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY & EMC| SAFETY STANDARDS Note.a| UL8750, CSAC22.2 No. 250.0-08, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent, BS EN/EN62384, EAC TP TC 004, IP67, GB19510.1,GB19510.14 approved; design refer to UL60950-1
WITHSTAND VOLTAGE| I/P-O/P:3.75KVAC
ISOLATION RESISTANCE| I/P-O/P:100M Ohms/ 500VDC / 25″C/ 70% RH
EMC EMISSION Note.a| Compliance to BS EN/EN55015,BS EN/EN61000-3-2 Class C (@load;:,; 60%); BS EN/EN61000-3-3, GB17743 and GB17625.1,EAC TP TC 020
EMC IMMUNITY| Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Line 2KV),EAC TP TC 020
OTHERS| MTBF| 3614.1K hrs min. Telcordia SR-332 (Bellcore); 396.7Khrs min. MIL-HDBK-217F (25’C)
DIMENSION| 162.5’43’32mm (L’W’H)
PACKING| 0.45Kg; 32pcs/15.4Kg/0.93CUFT
NOTE|

All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25’C of ambient temperature.
Please refer to “DRIVING METHODS OF LED MODULE”.
Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
Tolerance : includes set up tolerance , line regulation and load regulation.
De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains.
This series meets the typical life expectancy of >50,000 hours of operation when Tease, particularly@) point (or TMP, per DLC), is about ?O”C or less.
Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com
The ambient temperature derating of 3.5″C/1000m with fanless models and of 5°C /1000mwith fan models for operating altitude higher than 2000m(6500ft).
For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf ;)); Product Liability Disclaimer : For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

BLOCK DIAGRAM

DRIVING METHODS OF LED MODULE

DIMMING OPERATION

* 3 in 1 dimming function

DIMMING OPERATION

Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1 – 1 0VDC, or 1 0V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
Dimming source current from power supply: 1 00μA (typ.)
© Applying additive 1 – 1 0VDC

DIMMING OPERATION

© Applying additive 10V PWM signal (frequency range 100Hz- 3KHz):

DIMMING OPERATION

© Applying additive resistance:

DIMMING OPERATION

Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.