Wohua Toys Factory S911 Mini High Speed Car User Manual
- June 9, 2024
- Wohua Toys Factory
Table of Contents
Wohua Toys Factory S911 Mini High Speed Car
User Manual
Packing list
Battery installation and charging of remote control car and remote
control
Connect the battery to the USB cable, plug the USB cable into the USB port of
the computer or the USB charger, and turn on the power. When the red light is
on, it means charging. When the red light is off, it means fully charged.
Battery installation method of remote control
- Open the battery cover on the bottom of the remote control
- Install 2 1.5V “AA” batteries with correct polarity and close the battery cover.
Function of remote control
Operation method
- Turn the power switch of the remote control vehicle to the “ON” position. Put the remote control car on the plane, and then turn on the remote control switch. When the remote control indicator stops flashing, you may operate the control lever.
(Note: when the remote control indicator is flashing, the control lever can not be operated.)
Basic operation diagram for production use
- Pull the remote control lever backward to move the remote control car forward, and pull forward to move the remote control car backward. When the control lever is pulled backward half way, the remote control car will move forward slowly; when the control lever is pulled backward completely, the remote control car will move forward rapidly.
- If you turn the “right/ right steering wheel” clockwise, the car will turn right; if you turn the “left / left steering wheel” counter-clockwise, the car wit turn left.
- The high / low speed button is in low-speed gear in default when leaving the factory. You press the switch button once and the car light flashes twice to switch to the high-speed gear, and then press the switch button once again to switch to the low-speed gear.
- Light switch: press to turn on the body light, and then press to turn off the body light.
Maintenance and repair
- If you do not use it for a long time, please take out the battery.
- Wipe the car gently with a wet cloth.
- Do not put the product in high temperature, high humidity and direct sunlight.
- Do not put the product in the water, or the electronic components will be damaged.
Precautions
- Please pay attention to the polarity when installing or replacing the battery;
- Non-rechargeable battery can not be charged; ·Charging a rechargeable battery should be supervised by adult;
- Do not use old or new batteries or different types of batteries;
- Please pay attention to the signal interference nearby during operation, otherwise the remote control distance will be affected;
- When the remote control car slows down, it means that the car is out of power. Please charge the remote control car according to the above method. • If the remote control is out of power, the indicator will turn dark or does not light up. Please replace the battery with a new one.elf you do not use it for a long time, please take out the battery in the remote control, turn the power switch of the remote control car to “OFF” position, and take out the battery of the remote control car.
Warm tips
When the car is moving, please do not touch the wheels of the remote control car by hand, so as to avoid damage to the car.
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>