PERRIN ROWE AUSH.4417 Pot Filler Instruction Manual
- June 13, 2024
- PERRIN ROWE
Table of Contents
PERRIN ROWE AUSH.4417 Pot Filler Instruction Manual
AUSH.4417
AUSH.4417CP: Chrome
AUSH.4417NI: Nickel
AUSH.4417PF: Pewter
AUSH.4417SB: Satin Brass
AUSH.4417EB: English Bronze
AUSH.4417BR: Polished Brass
AUSH.4417IG: Gold (special order)
Temperature range: Min 1°C. Max 70°C
Working Pressure: Min 100kPa (14.5psi). Max 500kPa (72.5psi)
Flow Rate: Regulated to 8.3L/min
IMPORTERS & DISTRIBUTORS OF FINE KITCHEN AND BATHROOMWARE
07 3265 7133 | 30 French Avenue, Brendale QLD 4500 |
aftersales@luxebydesign.com.au |
www.luxebydesign.com.au
Congratulations on the purchase of your Shaws by Perrin & Rowe kitchen product. Correctly installed and with sensible care, this product will give you many years of trouble-free service.
INSTALLATION REQUIREMENTS
Perrin & Rowe tapware must be installed by a Licensed Plumber in accordance with the installation instructions provided, best trade practices and must comply to local plumbing regulations in your area. Incorrect installation may damage your tap and could invalidate your warranty.
- Where the inlet water pressure exceeds 500kpa, pressure limiting valves must be installed.
- In-line gauze filters must be fitted in the incoming water supply lines.
- Prior to installation, it is important to flush all incoming water lines thoroughly. Failure to do so may result in issues caused by debris in the water supply such as bits of metal or plastic, dirt, sand, rust, silt, and other unwanted materials. Any problems that arise as a result of inadequate flushing may not be covered by the warranty.
- Please take care of this product before, during and after installation as accidental damage to the tap finish is not covered by the warranty. Please wear gloves when handling ‘living finish’ models. If further work is to be carried out in the vicinity of the product, please cover it to protect from paint, plaster, adhesives, sealants and cleaning products.
- For ease of possible future servicing, we recommend the fitting of conveniently placed isolating valves.
- Once unpacked, remove fixing nuts, clamp plate, fibre washer and plastic backnut from tap assembly, ready for installation.
CARE AND MAINTENANCE
Perrin & Rowe taps and accessories are made in Britain from premium quality brass. Each piece is hand polished and electroplated in a range of beautiful finishes. While our finishes exceed industry standards for thickness and quality, they need appropriate care to maintain the beauty of the product and to preserve your warranty.
Following a simple cleaning routine after use will maintain the beauty of your brassware, and preserve the warranty. Ideally, fittings should be dried with a soft cloth after each use. Clean regularly by dampening a microfibre cloth with warm water combined with a mild PH-neutral liquid soap, then polish with a soft, lint-free cloth to finish. Microfibre cloths are ideal as they are gentle but effective at cleaning brassware without scratching. This approach is suitable for all finishes, except for Gold which should be dried with a leather chamois cloth.
General Tips for all Finishes
- Dry fittings after use with a soft cloth.
- Residue left from personal hygiene products such as soap or cleaning gels can cause blemishes on your brassware. Completely rinse off all fittings with clean water, and dry after use.
- Avoid getting bleach or harsh chemicals and cleaners on your taps when cleaning surrounding surfaces. Covering your fixtures with a cloth or towel reduces the risk of damaging your brassware finishes.
- To remove limescale, use a 50/50 solution of lemon juice and water. Soak cotton wool in the solution and leave wrapped around the tap for no longer than 1 hour, then rinse clean with water and fully dry with a lint-free cloth. For heavy scaling, the process can be repeated provided the area is rinsed with clean water between treatments to avoid a build-up of citric acid.
Avoiding Damage
- Under no circumstances should harsh cleaning agents containing acidic, caustic or abrasive components such as bleach, alcohol or vinegar-based substances be used.
- Do not use abrasive cloths, scouring pads, scrub sponges, steel wool etc. as they may damage the surface.
- To avoid dye and patterning transfer from wet cloths, avoid hanging them over the spout of the tap. Porous surfaces such as nickel, pewter and unlacquered brass finishes may be affected by chemicals in or on the cloth. Damage caused through the actions described above would not be covered by Perrin & Rowe’s warranty.
WARRANTY AND LIABILITY
Perrin & Rowe tapware, or Shaws x Perrin & Rowe tapware and accessories sold by Luxe by Design in Australia, or via an authorised Australian dealer are warranted to be free from manufacturing defects in the materials and workmanship for 15 years from the date of purchase. Proof of purchase is required and all claims must be accompanied by an Australian approved retail sales invoice.
The Tapware Warranty outlined is subject to the product being installed correctly by a Licensed Plumbed in accordance with the installation instructions and adhering to local, state and Australian regulations (AS/NZS 3500). Additionally, in-line gauze filters should be installed, water temperature limitations should be adhered to, and the water supply lines must be adequately flushed before installing the product.
This warranty does not cover damages, defects, or malfunctions resulting from normal wear and tear, incorrect installation or maintenance, accidents, neglect, vandalism, misuse, alterations, modifications, unusual physical or environmental conditions or using the product in an unintended or non- designated application. The warranty does not apply to damage from the use of harsh, abrasive or corrosive cleaners. Please refer to our complete warranty document for full details.
Tapware Warranty
SERVICING AND WARRANTY CLAIMS
To initiate a warranty claim, please contact the dealer from whom the product
was purchased. Proof of purchase will be required. Warranty and servicing
claims will be processed by Luxe by Design during regular business hours via a
nominated service agent in state capital cities.
The customer will be asked to provide an detailed description of the alleged fault, along with photos or a video to assist in identifying the problem or cause. If Perrin & Rowe determines that a replacement part can be easily installed by the customer to resolve an issue covered by this warranty, the option to provide parts only as a resolution is reserved. In such cases, Luxe by Design will cover the freight costs associated with sending the replacement parts to the customer.
Luxe by Design may request the return of the alleged faulty part for warranty assessment, at their discretion. It’s important to note that if replacement products or parts are provided under warranty, the original warranty period remains unchanged and unaffected.
SPARES
If required, spare parts are available for your tap. Refer to the diagram below, taking special note of parts indicated with an asterisk as the finish colour will also need to be specified: Chrome (CP), Nickel (NI), Pewter (PF), English Bronze (EB), Satin Brass (SB), Polished Brass (BR) or Gold (IG). Please note, gold is a special order finish and may have a longer lead time for spares.
WATERMARK
Perrin & Rowe manufactures kitchen taps especially for the Australian market using DZR (dezincification resistant) brass of the highest quality, with fittings which are compatible with Australian plumbing standards. WaterMark certification (license number WMKA02818) has been awarded to the Perrin & Rowe tapware which is made for Australia. Perrin & Rowe tapware sold elsewhere in the world is not certified for Australia, contains different brass and plumbing fittings and cannot be legally installed.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>