PERRIN ROWE Rohl Authentic Luxury for Kitchen And Bath Installation Guide

: June 13, 2024
: PERRIN ROWE

Table of Contents

PERRIN ROWE Rohl Authentic Luxury for Kitchen And Bath
IMPORTANT INFORMATION
Parts
Preparation for Installer
Contact
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PERRIN ROWE Rohl Authentic Luxury for Kitchen And Bath

PERRIN-ROWE-Rohl-Authentic-Luxury-for-Kitchen-And-Bath-
product

The Perrin and Rowe Collection Filter Installation Guide

Congratulations on the purchase of your Perrin and Rowe/Triflow filtration Product. Correctly installed and with sensible care, this product will give you many years of trouble free service.

IMPORTANT INFORMATION

These are instructions for Triflow filters and the optional add on pre-filter version of the model you are installing. Please read carefully to ensure correct installation.
Before you proceed… We recommend you engage the services of a registered plumber to install this product.
In addition to the guide below it is essential that the written information overleaf is carefully read and understood.

Parts

U.1812 Triflow Filter Fitted with U.1802 filter

PERRIN-ROWE-Rohl-Authentic-Luxury-for-Kitchen-And-Bath-
fig-1

U.1816 Pre-Filter Fitted with .1620 filter

Temp Range:
- Max 85°C/185°F Recommended
Working Pressure:
- Min 1.7bar/25psi
- Max 5bar/75psi

Preparation for Installer

Flush the plumbing system before installing the Kitchen product

Install the supplied stop valve in an easily accessible area to allow access to turn off the water supply in the future, for servicing and cartridge replacement.
Position the filter housing leaving room around it for future access and cartridge replacement. Mark the screw holes ready for pilot holes. Leave room for the Pre-filter housing if necessary.

Ensure you have the correct fittings to connect to the filter faucet

Drill the pilot holes and screw the filter housing bracket in position. Making sure to keep as level as possible.

Flow direction

PERRIN-ROWE-Rohl-Authentic-Luxury-for-Kitchen-And-Bath-
fig-6

Flow direction

PERRIN-ROWE-Rohl-Authentic-Luxury-for-Kitchen-And-Bath-
fig-7

Tighten the hoses from the stop valve to the housings following the flow of the water shown on the cap.
If installing a Pre-filter the system flows from the stop valve to the Pre-filter and on to the filter housing and then up to the filter tap.

Filter Connectior Kit

PERRIN-ROWE-Rohl-Authentic-Luxury-for-Kitchen-And-Bath-
fig-8

Turn on the main supply valve. Run the filtered water for 2 minutes to flush the system, and carefully check the system for leaks. The system is now ready for use. For optimum filter performance when using the U.1802 filter cartridge use the stop valve to set a water flow of 0.4gpm to 0.5gpm max.

To Winterize the Unit

PERRIN-ROWE-Rohl-Authentic-Luxury-for-Kitchen-And-Bath-
fig-10

Shut off mains supply. A stop valve was supplied with the system for this purpose, and will be located on the adjacent pipe work.
If you plan to be away from home for extended periods, carry out the procedures above, to prevent the risk of freezing. Freezing will invalidate the warranty.
Turn the filtered lever on the faucet to the on position. This will confirm the water supply is off, and release the pressure in the system.

Pre-filter Installation

If installing a Pre-filter follow steps 1-3 for the second bracket taking into account the hose length supplied from the Pre-filter to the filter.
Tighten the hoses from the stop valve to the housings following the flow of the water shown on the cap. When installing the Pre-filter the system flows from the stop valve to the Pre-filter and on to the filter housing and then up to the filter tap.