COOPER LIGHTING SWPD2 WaveLinx Industrial Standalone Sensor Kit Instruction Manual

COOPER LIGHTING SWPD2 WaveLinx Industrial Standalone Sensor Kit

Instruction Manual

General Information

Overview
The industrial high bay and low bay sensors are an integral part of the WaveLinx Connected Lighting System and offer passive infrared (PIR) occupancy and a photocell for closed loop daylighting. WaveLinx industrial sensors offer installation heights up to 40 feet and have coverage patterns up to 5000 square feet (see sensor specifications – field of view). When part of WaveLinx, the sensor operates on a wireless mesh network based on IEEE 802.15.4 standards.

The sensors offer simple tool-less integration into WaveLinx industrial light fixtures equipped with the 4-pin Zhaga Book 18 compliant socket (including sidecar). Once installed, sensors receive power from their co-located light fixture with no batteries to replace. The sensor in combination with the WaveLinx Mobile application allows you to gain considerable energy savings from occupancy and daylight sensing lighting control. The Wave Linx Mobile application allows you to map the sensor to any area or control zone, select occupancy or vacancy, occupied and unoccupied light levels and set the hold time.

Specifications

Technology: WaveLinx industrial sidecar sensor for downlight fixtures control based on IEEE 802.15.4. Compatible only with Cooper Lighting Solutions Lighting WaveLinx Wireless Systems.

Wiring Diagram

Installation

De-energize electrical circuit prior to work

1. Install the control module inside the fixture
2. Insert and secure the sidecar housing
3. Wire per the electrical diagram
4. Install the sensor (twist to lock)

Out-of-the-box functionality (if connected to loads)
Fixture operates via the onboard occupancy sensor.

• Occupancy turns fixture ON to 100%
• Fixture will dim to 10% within 20 minutes when space is vacant

Note: Daylighting is disabled until the fixture is assigned to an area using the WaveLinx Mobile Application.

Wireless setup

1. Upon power up, the WaveLinx Industrial Sidecar Sensor Kit will search for an Cooper Lighting Solutions WaveLinx wireless network while powering connected luminaires to 100% when occupied.
2. When the WaveLinx Industrial Sidecar Sensor Kit locates and successfully joins a WaveLinx wireless network, the connected luminaires will dim to 10% (if using 0-10V wiring)
3. This feature is used to visually inspect which sensors successfully join the wireless network.
4. Industrial sidecar sensors that did not pair correctly will remain at 100% (0-10V) or 100% (no 0-10V).
5. When the pairing is complete all industrial sidecar sensors become part of the default area and dimmable zone.
   Note: Please refer to WaveLinx manual to complete configuration.

LED Indicator Definitions

There are two major LED patterns for the WaveLinx Industrial Sidecar Sensor:

• When the industrial sidecar sensor is not connected to the WaveLinx wireless network the LED in the sensor will blink Green.
• When the industrial sidecar sensor is connected to the WaveLinx network the LED in the sensor will blink White.

Troubleshooting

**** WARNING

IMPORTANT: Read carefully before installing product. Retain for future reference.

DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product.

NOTICE: Product may become damaged and/or unstable if not installed properly.

ATTENTION Receiving Department: Note actual product description of any shortage or noticeable damage on delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days of delivery. All damaged material, complete with original packing must be retained.

Note: Specifications and dimensions subject to change without notice.
NOTICE: Designed for indoor installation and use only. Wet location listed.
Must not exceed 20 drivers connected to a single Tilemount sensor dimming wires.
Must not exceed 70 °C operating environment.
Blue wire switches to Line voltage. Do not handle while powered.
Dimming luminaires should not connect 0-10V wires from different line powered circuits.
Failure to comply with these instructions may result in death, serious bodily injury and property damage.

Warranties and Limitation of Liability

Please refer to www.cooperlighting.com for our terms and conditions.
FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Part 15 Clause 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Part 15.19a This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC 2.1091/RSS-102 In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times.

ISED RSS
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-3 (B)/NMB-3(B)

Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
www.cooperlighting.com
Pour obtenir de l’aide technique
ou un service :
1 800 553-3879

www.cooperlighting.com

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>