MEAN WELL HBGC-300-L 300W HBGC Series Constant Power LED Driver Owner’s Manual

MEAN WELL HBGC-300-L 300W HBGC Series Constant Power LED Driver

Features

• Wide input range 90 ~ 305VAC
• Full power at 60~100% max current (Constant Power)
• Built-in active PFC function
• Circular metal housing design with IP67
• Function options: output adjustable via potentiometer; 3 in 1 dimming (Dim to off and Isolation) ; DALl-2 dimming
• Typical lifetime>50000 hours
• 5 years warranty
  

Applications

• Bay lighting
• Stage lighting
• Flood lighting
• Stadium lighting
• Type HL for use in class I ,Division 2

Description

HBGC-300 series is a 300W LED AC/DC driver featuring the constant power mode and high voltage output. HBGC-300 operates from 90~305VAC and offers models with different rated current ranging between 1300mA and 8670mA. Thanks to the high efficiency up to 94.5%, with the fanless design, the entire series is able to operate for -40°C~+80°C case temperature under free air convection. The design of metal housing and IP67 ingress protection level allows this series to fit both indoor and outdoor applications. Moreover the innovative environment-adaptive capability allows this series to reliably light on the LEDs for all kinds of application environments in almost any spots that may install LED luminaires in the world. HBGC-300 is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system.

Model Encoding

SPECIFICATION

INPUT

| VOLTAGE RANGE Note.2| 90- 305VAC        127VDC-431VDC

(Please refer to “STATIC CHARACTERISTIC” section)

FREQUENCY RANGE| 47 – 63Hz
POWER FACTOR (Typ.)| PF 0.97 / 115VAC, PF 0.95 / 230VAC, PF 0.92 / 277VAC at full load (Please refer to “Power Factor Characteristic” section)
TOTAL HARMONIC DISTORTION| THO< 10% (@load 50% at 115VAC/230VAC ,@load 75% at 277VAC) Please refer to “TOTAL HARMONIC DISTORTION (THO)” section
EFFICIENCY (Typ.)| 94.5%| 93.5%| 92.5%
AC CURRENT (Typ.)| 3A/ 115VAC       1.6A/ 230VAC        1.3A/ 277VAC
INRUSH CURRENT(Typ.)| COLD START 45A (t width=1300µs measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. NO. of PSUs on 16A CIRCUIT BREAKER| ****

2 unit(circuit breaker of type B) / 4 units(circuit breaker of type C) at 230VAC

LEAKAGE CURRENT| <0.75mA/ 277VAC
NO LOAD/ STANDBY POWER CONSUMPTION| Standby power consumption <0.5W for AB/ ADA-Type Blank/A-Type please refer to Note. 5
PROTECTION| SHORT CIRCUIT| Constant current limiting, recovers automatically after fault condition is removed
OVER VOLTAGE| 241 -275V| 121 -145V| 61 – 78V
Shut down output voltage, re-power on to recovery
OVER TEMPERATURE| Tcase>BO”C ±5″C,derate power automatically by 6°/JC max.
ENVIRONMENT| WORKING TEMP.| Tcase=-40 – +80’C(Please refer to “OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP.| Tcase=+80″C
WORKING HUMIDITY| 20 – 95% RH non-condensing
STORAGE TEMP., HUMIDITY| -40 – +B0″C , 1O – 95% RH non-condensing
TEMP. COEFFICIENT| ± 0.03%/°C (0 – 60°C)
VIBRATION| 10-500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY & EMC| SAFETY STANDARDS| UL8750(type”HL”), CSA C22.2 No. 250.13-12; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent, BS EN/EN62384; EAC TP TC 004;GB19510.1 , GB19510.14; IP67 approved
DALI STANDARDS| Compliance to IEC62386-101, 102,207 for ADA Type only
WITHSTAND VOLTAGE| I/P-0/P 3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
ISOLATION RESISTANCE| I/P-0 /P, I/P-FG, O/P-FG:100M Ohms/ 500VDC / 25″C/ 70% RH
EMC EMISSION| Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@ load 50%); BS EN/EN61000-3-3,EAC TP TC 020
EMC IMMUNITY| Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547, light industry level (surge immunity Line-Earth 6KV, Line-Line 4KV), EAC TPTC 020

OTHERS

| MTBF| 561.2K hrs min.    Telcordia SR-332(Bellcore); 154.9K hrs min. MIL-HDBK-217F (25″C)
LIFETIME Note.4| 50000 hrs min.
DIMENSION| rp 191.5mm ’69mm
PACKING| 2.2Kg;Bpcs/19 .8Kg/2.09CUFT
NOTE|

1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25°C of ambient temperature.
2. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
3. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
4. This series meets the typical life expectancy of >50,000 hours of operation when Tease, particularly tc point (or TMP, per DLC), is about 75″C or less.
5. To fulfill requirements of the latest ErP regulation for lighting fixture, this LED drive can only be used behind a switch without permanently connected to the mains.
6. Please refer to the warranty statement on MEAN WELL’s website at http: / /www.meanwell.com
7. The ambient temperature derating of 3.5°C/ 1000m with fanless models and of 5°C /1000m with fan models for operating altitude higher than 2000m(6500ft).
8. For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf

• Product Liability Disclaimer : For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

BLOCK DIAGRAM

PFC KH fosc : 45~50 z
PWM KH fosc : 60~130 z

DRIVING METHODS OF LED MODULE

※ I V Operating Area –

• HBGC-300-L
  

• HBGC-300-M
  

• HBGC-300-H
  

DIMMING OPERATION

※ 3 in 1 dimming function (for AB-Type)

• Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-:
  0 ~ 10VDC, or 10V PWM signal or resistance.

• Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.

• Dimming source current from power supply: 100 A (typ.)

Applying additive 0 ~ 10VDC

Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):

Applying additive resistance:

Note :

1. Min. dimming level is about 8% and the output current is not defined when 0%< out<8%. I
2. The output current could drop down to 0% when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle.

OUTPUT LOAD vs TEMPERATURE

STATIC CHARACTERISTIC

POWER FACTOR (PF) CHARACTERISTIC

※ Tcase at 65℃

TOTAL HARMONIC DISTORTION (THD)

EFFICIENCY vs LOAD

HBGC-300 series possess superior working efficiency that up to 94.5% can be reached in field applications.

※ HBGC-300-L Model, Tcase at 65℃

LIFE TIME

MECHANICAL SPECIFICATION

•  : Max. Case Temperature.(case temperature measured point)
• Ta: Ambient Temperature measured point

• : Max. Case Temperature.(case temperature measured point)
• Ta: Ambient Temperature measured point

INSTALLATION MANUAL

Please refer to: http://www.meanwell.com/manual.html

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>