DrayTek VigorAP 1000C Wireless Tri Band Gigabit Ceiling Mount User Guide

: June 13, 2024
: DrayTek

Table of Contents

DrayTek VigorAP 1000C Wireless Tri Band Gigabit Ceiling Mount
Product Information
Product Usage Instructions
Package Content
Panel Explanation
Installation
Software Configuration
Customer Service
Regulatory Information
Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DrayTek VigorAP 1000C Wireless Tri Band Gigabit Ceiling Mount

Product Information

The VigorAP 1000C is an 802.11ac Ceiling-mount AP designed for wireless networking. It is equipped with the latest firmware version V1.4.2 and offers fast and reliable connectivity. The device has a maximum power consumption of 20 Watts and comes with different power adapters depending on the country of installation.

Package Content

Vigor Device
Quick Start Guide
Ethernet Cable
Mounting Bracket
Power Adapter (UK, EU, USA/Taiwan, or AU/NZ type)

Panel Explanation
The device panel features LED indicators and various connectors:

LED Indicators: 5G-2, 5G-1, 2.4G (showing wireless function status)
P2/P1(PoE) Connectors (Left and Right LEDs): indicate data transmission and LAN port connection status
RST Interface: used to restore default settings
P2/P1(PoE) USB Connector: for local networked devices and USB device connection

Product Usage Instructions

Installation
Before installing the VigorAP, please ensure that only trained and qualified personnel perform the installation for personal safety.

Mounting the Access Point:
Place the mounting bracket on the front side of the calcium silicate board.
Fasten the bracket securely using four screws.

Package Content

Please the package contents. If anything is missing or damaged, please contact DrayTek or your dealer immediately.

The type of power adapter depends on the country which the device will be installed. * The maximum power consumption is 20 watts.

Note

Remove the protective film from the router before use to ensure ventilation.

Panel Explanation

LED	Status	Explanation

5G-2

5G-1

2.4G

| On| Wireless function is ready.
Off| Wireless function is not ready.
Blinking| Data is being transmitted (sending/receiving).
P2 / P1(PoE)

(Left LED)

| On| The LAN port is connected.
Blinking| The data is transmitting.
Off| The LAN port is disconnected.
P2 / P1(PoE)

(Right LED)

| On| The LAN port is connected with a transmission rate of 1000Mbps.
Off| The LAN port is connected with a transmission rate of 10/100Mbps if left LED is on.

Note

Connector P1(PoE) is used for PoE connection (for indoor use only).

Installation

This section will guide you through installing the VigorAP.

Note

For the sake of personal safety, only trained and qualified personnel should install this access point.

VigorAP can be mounted on the board of calcium silicate. Below shows an exploded view of VigorAP installation.

Follow the steps listed below to mount the access point.

Place the bracket on the front side of the calcium silicate board and fasten it with four screws.
When the bracket is in place, reverse the board. Put the washer on the screw.
Insert the cap nut to the screw on the washer. Rotate the cap nut until it locks firmly on the washer.
There are four latches on the bracket. Put the device (VigorAP) on the bracket with the direction shown below.

Note
To remove the AP, please

A. Insert a small-sized flathead screwdriver to the locking notch.
B. Push to separate the device from the four latches.

Software Configuration

This section will guide you through the configuration of the settings using a web browser. Here we take VigorAP 1000C as an example.

Make sure your PC is connected to the access point correctly.
Open a web browser on your PC and type https://192.168.1.2. A pop-up window will open asking you for a username and password. Please type “admin/admin” for Username/Password and click Login.

Note
You may either set up your computer to receive an IP address dynamically from the access point or manually enter an IP address that is within the same subnet as the IP address of VigorAP.

If there is no DHCP server on the network, the VigorAP will have an IP address of 192.168.1.2.
If there is DHCP available on the network, the VigorAP will receive its IP address via the DHCP server.

Connected As a Mesh Node (in Mesh Network)

Install VigorAP in the place you want.
As a mesh node, settings related to this VigorAP must be configured by a remote Mesh Root within the mesh network. The user must detect this VigorAP via a Mesh Root to add it as a mesh node.

Connected As an Access Point

Connect VigorAP to a Vigor router.
Use a twisted-pair cable with RJ-45 plugs at both ends, and plug into Ethernet device (e.g., Vigor router) and Ethernet port of VigorAP.
There are two methods to configure VigorAP.
Method 1:
- (a) First, open a web browser on your PC and type https://192.168.1.2. A pop-up window will open to ask for username and password.
- (b) After clicking Login, Quick Start Wizard for configuring wireless settings will appear as follows.
- (c) Follow the on-screen steps to finish the network connection.
  Method 2:
- (a) Use a mobile phone to scan the QR code-named with DrayTek WirelessApp to download DrayTek Wireless APP.
- (b) After downloading, run the APP.
- (c) From the home page, click the Connect icon to access the Connect page. Next, press the QR code icon next to Scan QR Code on your phone screen to open the camera.
  Scan the QR code-named with Connect SSID to access the web user interface (configuration wizard) of VigorAP 1000C. (For iOS users, the SSID and the password will be shown first. Simply click the Connect button to access the web user interface of VigorAP.)

Customer Service

If the access point still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.

Be a Registered Owner
Web registration is preferred. You can register your Vigor device via
https://myvigor.draytek.com.

Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all devices will be regularly upgraded. Please consult the DrayTek website for more information on the newest firmware, tools, and documents. https://www.draytek.com

GPL Notice This DrayTek product uses software partially or completely licensed under the terms of the GNU GENERAL PUBLIC LICENSE. The author of the software does not provide any warranty. A Limited Warranty is offered on DrayTek products. This Limited Warranty does not cover any software applications or programs.

To download source codes please visit:
https://gplsource.draytek.com
GNU GENERAL PUBLIC LICENSE:
https://gnu.org/licenses/gpl-2.0
Version 2, June 1991
For any question, please feel free to contact DrayTek technical support at support@draytek.com for further information.

Intellectual Property Rights (IPR) Information

Copyrights| © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders.
---|---
Trademarks| The following trademarks are used in this document:

l Microsoft is a registered trademark of Microsoft Corp.

l Windows, Windows 7, 8, 10 and Explorer are trademarks of Microsoft Corp.

l Apple and Mac OS are registered trademarks of Apple Inc.

l Other products may be trademarks or registered trademarks of their respective manufacturers.

Safety Instructions and Approval

Safety Instructions| l Read the installation guide thoroughly before you set up the access point.

l The access point is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the device yourself.

l Keep the package out of reach of children.

l When you want to dispose of the access point, please follow local regulations on conservation of the environment.

---|---
Warranty| We warrant to the original end user (purchaser) that the device will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects that do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revisions or changes.

Regulatory Information

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device may accept any interference received, including interference that may cause undesired operation. The antenna/transmitter should be kept at least 20 cm away from human body.
For more updates, please visit www.draytek.com.

USA Local Representative

| Company name| ABP International Inc.
---|---|---
Address| 13988 Diplomat Drive Suite 180 Dallas TX 75234
ZIP Code| 75234| E-mail| rmesser@abptech.com
Contact Person| Mr. Robert Messer| Tel.| 19728311600

Declaration of Conformity

Hereby, DrayTek Corporation declares that the radio equipment type VigorAP 1000C is in compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following internet address: https://www.draytek.com.tw/ftp/VigorAP1000C/Document/CE/

Manufacturer : DrayTek Corp.
Address : No. 26, Fushing Rd, Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan
Product : VigorAP 1000C
Frequency Information for Europe area:

2.4G WLAN	2412MHz – 2472 MHz, max. TX power: 19.5 dBm *1
5G WLAN	5170MHz – 5330 MHz, max. TX power: 22 dBm 5480MHz – 5720 MHz, max. TX

power: 27 dBm *2
|

Requirements in UK. 5150MHz – 5350MHz is for indoor use only.

(1: for 2.4G WLAN model; 2: for 5G WLAN model)
This product is designed for 2.4GHz/5GHz WLAN network throughout the EC region.

Hereby, DrayTek Corporation declares that the radio equipment type VigorAP 1060C is in compliance with Regulation SI 2017 No. 1206.
The full text of the UKCA Declaration of Conformity is available at the following internet address:
https://www.draytek.com.tw/ftp/VigorAP1000C/Document/UKCA/
Manufacturer: DrayTek Corp.
Address: No. 26, Fushing Rd, Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan
Product: VigorAP 1000C
Importer: SEG, 11 Capital Business Park, Borehamwood, Herts, WD6 1GW
Frequency Information for UK area:

2.4G WLAN	2412MHz – 2472 MHz, max. TX power: 19.5 dBm *1
5G WLAN	5170MHz – 5330 MHz, max. TX power: 22 dBm 5480MHz – 5720 MHz, max. TX

power: 27 dBm *2
|

Requirements in UK. 5150MHz – 5350MHz is for indoor use only.

(1: for 2.4G WLAN model; 2: for 5G WLAN model)
This product is designed for 2.4GHz and 5GHz WLAN network use in the UK & Ireland.
*The external power supply used for each product will be model dependent.

| | 1| 2| 3| 4| 5| 6| 7| 8| 9
---|---|---|---|---|---|---|---|---|---|---
A| Manufacturer| CWT| CWT| CWT| CWT| CWT| APD| APD| APD| APD
B| Address| No. 222, Sec. 2,