DrayTek Vigor2927ac Dual WAN Security Router User Guide
- October 30, 2023
- DrayTek
Table of Contents
- Intellectual Property Rights (IPR) Information
- Safety Instructions and Approval
- EU Declaration of Conformity
- Regulatory Information
- Package Content
- Panel Explanation
- Hardware Installation
- Software Configuration
- Customer Service
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Vigor2927ac Dual WAN
Security Router
User Guide
Intellectual Property Rights (IPR) Information
Copyrights| © All rights reserved. This publication contains information
that is protected by copyright. No part may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language
without written permission from the copyright holders.
---|---
Trademarks| The following trademarks are used in this document:
- Microsoft is a registered trademark of Microsoft Corp.
- Windows, 8, 10 and Explorer are trademarks of Microsoft Corp.
- Apple and Mac OS are registered trademarks of Apple Inc.
- Other products may be trademarks or registered trademarks of their respective manufacturers. Copyrights Trademarks
Safety Instructions and Approval
Safety Instructions|
- Read the installation guide thoroughly before you set up the router.
- The router is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the router yourself.
- Do not place the router in a damp or humid place, e.g. a bathroom.
- Do not stack the routers.
- The router should be used in a sheltered area, within a temperature range of +5 to +40 Celsius.
- Do not expose the router to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.
- Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.
- Keep the package out of reach of children.
- When you want to dispose of the router, please follow local regulations on conservation of the environment.
---|---
Warranty| We warrant to the original end user (purchaser) that the
router will be free from any defects in workmanship or materials for a period
of two (2) years from the date of purchase from the dealer. Please keep your
purchase receipt in a safe place as it serves as proof of date of purchase.
During the warranty period, and upon proof of purchase, should the product
have indications of failure due to faulty workmanship and/or materials, we
will, at our discretion, repair or replace the defective products or
components, without charge for either parts or labor, to whatever extent we
deem necessary tore-store the product to proper operating condition. Any
replacement will consist of a new or re-manufactured functionally equivalent
product of equal value, and will be offered solely at our discretion. This
warranty will not apply if the product is modified, misused, tampered with,
damaged by an act of God, or subjected to abnormal working conditions. The
warranty does not cover the bundled or licensed software of other vendors.
Defects which do not significantly affect the usability of the product will
not be covered by the warranty. We reserve the right to revise the manual and
online documentation and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or changes.
** EU Declaration of Conformity**
We DrayTek Corp. , office at No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan, declare under our sole responsibility that the product
- Product name: Dual-WAN Security Router
- Model number: Vigor2927
- Manufacturer: DrayTek Corp.
- Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan.
is in conformity with the relevant Union harmonization legislation:
EMC Directive 2014/30/EU , Low Voltage Directive 2014/35/EU, ErP 2009/125/EC
and RoHS 2011/65/EU with reference to the following standards
Standard | Version/Issue date |
---|---|
EN 55032 | 2015+AC:2016 class B |
EN 61000-3-2 | 2014 Class A |
EN 61000-3-3 | 2013 |
EN 55024 | 2010+A1:2015 |
EN 62368-1 | 2014+A11:2017 |
EN IEC 63000:2018 | 2018 |
EC No. 1275/2008 | 2008 |
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference
that may cause undesired operation.
USA Local Representative | Company name | ABP International Inc. |
---|---|---|
Address | 13988 Diplomat Drive Suite 180 Dallas TX 75234 | |
ZIP Code | 75234 | |
Contact Person | Mr. Robert Messer | Tel. |
Caution:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
*The external power supply used for each product will be model dependent.
Package Content
Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Besides, the content is subject to the real package.
The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 22 Watt.
UK-type Power
Adapter| EU-type Power
Adapter
---|---
USA/Taiwan-type Power
Adapter| AU/NZ-type Power
Adapter
Panel Explanation
Vigor2927
No. | LED | Status | Explanation |
---|---|---|---|
(1) | ACT | Off | The router is powered off. |
Blinking | The router is powered on and running normally. | ||
WAN2/WAN1 | On | Internet connection is ready. | |
Off | Internet connection is not ready. | ||
Blinking | The data is transmitting. | ||
USB1/USB2 | On | USB device is connected and ready for use. | |
Off | No USB device is connected. | ||
Blinking | The data is transmitting. | ||
DMZ | On | The DMZ function is enabled. | |
Off | The DMZ function is disabled. | ||
Blinking | The data is transmitting. | ||
QoS | On | The QoS function is active. | |
Off | The QoS function is inactive. | ||
VPN | On | The VPN tunnel is active. | |
Off | VPN services are disabled | ||
Blinking | Traffic is passing through VPN tunnel. | ||
WCF | On | The Web Content Filter is active. (It is enabled from **Firewall >> |
General Setup**).
Off| WCF is disabled.
(2)| WAN1,WAN2 / P6
Left LED| On| The port is connected.
Off| The port is disconnected.
Blinking| The data is transmitting.
Right LED| On| The port is connected with 1000Mbps.
Off| The port is connected with 10/100Mbps.
LAN P1-P5
Left LED| On| The port is connected.
Off| The port is disconnected.
Blinking| The data is transmitting.
Right LED| On| The port is connected with 1000Mbps.
Off| The port is connected with 10/100Mbps
No. | Interface | Description |
---|---|---|
(3) | Factory Reset | Restore the default settings. Usage: Turn on the router |
(ACT LED is blinking). Press the hole and keep for more than 5 seconds. When
you see the ACT LED begins to blink rapidly than usual, release the button.
Then the router will restart with the factory default configuration.
(4)| USB| Connecter for a USB device (for 3G/4G USB Modem or printer or
thermometer).
(5)| WAN1| Connecter for local network devices or modem for accessing
Internet.
WAN2 / P6| Connecter for local network devices or modem for accessing
Internet.It is a switchable port. It can be used for LAN connection or WAN
connection according to the settings configured in WUI.
LAN P1-P5| Connecters for local network devices.
(6)| PWR| Connecter for a power adapter.
ON/OFF| Power Switch.
Hardware Installation
This section will guide you to install the router through hardware connection
and configure the router’s settings through web browser.
Before starting to configure the router, you have to connect your devices
correctly.
Network Connection
- Connect the cable Modem/DSL Modem/Media Converter to any WAN port of router with Ethernet cable (RJ-45).
- Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router and the other end of the cable (RJ-45) into the Ethernet port on your computer.
- Connect one end of the power adapter to the router’s power port on the rear panel, and the other side into a wall outlet.
- Power on the device by pressing down the power switch on the rear panel.
- The system starts to initiate. After completing the system test, the ACT LED will light up and start blinking. (For the detailed information of LED status, please refer to section 3. Panel Explanation)
Wall-Mounted Installation
Vigor router has keyhole type mounting slots on the underside.
- Drill two holes on the wall. The distance between the holes shall be 168mm.
- Fit screws into the wall using the appropriate type of wall plug.
| The recommended drill diameter shall be 6.5mm (1/4”).
---|---
Software Configuration
To access Internet, please finish basic configuration after completing the
hardware installation.
The Quick Start Wizard is designed for you to easily set up your router
for Internet access. You can directly access the Quick Start Wizard via Web
User Interface. Make sure your PC connects to the router correctly.
| You may either simply set up your computer to get IP dynamically from the
router or set up the IP address of the computer to be the same subnet as the
default IP address of Vigor router 192.168.1.1. For the detailed
information, please refer to – Trouble Shooting of the user’s guide.
---|---
Open a web browser on your PC and type http://192.168.1.1. A pop-up window
will open to ask for username and password. Please enter “admin/admin” as the
Username/Password and click Login.
| If you fail to access to the web configuration, please go to “Trouble
Shooting” on User’s Guide for detecting and solving your problem.
---|---
Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard.
| The home page will change slightly in accordance with the router you have.
---|---
If your router can be under an environment with high speed NAT, the
configuration provide here can help you to deploy and use the router quickly.
The first screen of Quick Start Wizard is entering login password. After
typing the password, please click Next.
On the next page as
shown below, please select the WAN interface that you use.
If Ethernet interface is used, please choose WAN1 or WAN2; if wireless 2.4G/5G
connection is used, please choose WAN3 or WAN4; if 3G USB modem is used,
please choose WAN5 or WAN6. Then click Next for next step. Each WAN
interface will bring up specific configuration page.
Click Next. You have to select the appropriate Internet access type
(PPPoE, PPTP, L2TP, Static IP or DHCP) according to the information from your
ISP.
Here we take PPPoE and DHCP modes for WAN connection as examples.
For PPPoE Connection
-
Choose WAN1 as WAN Interface and click the Next button; you will get the following page.
-
Select PPPoE and click Next to get the following page.
-
Enter the Username/Password provided by your ISP. Then click Next for viewing the summary of such connection.
-
Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
-
Now, you can enjoy surfing on the Internet.
For DHCP Connection
-
Choose WAN1 as WAN Interface and click the Next button; you will get the following page.
-
Select DHCP and click Next to get the following page
-
Enter the hostname and / or MAC address provided by your ISP. Then click Next for viewing summary of such connection.
-
Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
-
Now, you can enjoy surfing on the Internet.
Customer Service
If the router cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.
Be a Registered Owner
Web registration is preferred. You can register your Vigor router via
https://myvigor.draytek.com.
Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek web site for more information
on newest firmware, tools and documents.
https://www.draytek.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>