DrayTek VigorSwitch G1085 Web Smart Gigabit Switch User Guide
- October 30, 2023
- DrayTek
Table of Contents
Vigor Switch G1085
Web Smart Gigabit Switch
Quick Start Guide
Version: 1.2
Firmware Version: V2.6.7
(For future update, please visit Dray Tek web site)
Date: March 7, 2023
Package Content
The type of the power cord depends on the country that the switch will be installed.
If any of these items is found missing or damaged, please contact your local supplier for replacement.
Panel Explanation
LED | Status | Explanation |
---|---|---|
SYS | On (Green) | The switch finishes system booting and the system is ready. |
Blinking (Green) | The switch is powered on and starts system booting. | |
Off | The power is off or the system is not ready /malfunctioning. | |
PWR | On (Green) | The device is powered on and running normally. |
Off | The device is not ready or is failed. | |
Interface | Description | |
--- | --- | |
RST | Factory reset button. |
l Press it to reboot the system. (<5 seconds)
The SYS LEDs will blink too.
l Press it to reset the system with factory default settings. (5~20 seconds)
The SYS LED will be off if RST button is pressed between 5 seconds and 10
seconds.
RJ 45 LNK/ACT Port 1 ~ 8| Port 1 to Port 8 are used for Ethernet connection.
| Power inlet for AC input (100~240V/AC, 50/60Hz).
Hardware Installation
Before starting to configure the switch, you have to connect your devices
correctly.
3.1 Network Connection
Use the Ethernet cable(s) to connect None-PoE devices to the Vigor switch. All
device ports are in the same local area network.
3.2 Rack-Mounted Installation
The switch can be installed easily by using rack mount kit. 1. Fasten the rack
mount kit on both sides of the Vigor Switch using specific screws. 2. Then,
install the Vigor Switch (with rack mount kit) on the 19-inch chassis by using
other four screws.
Software Configuration
Before using the switch, perform the following steps:
- Set up a physical path between the configured the switch and a PC by a qualified UTP Cat. 5e cable with RJ-45 connector.
If a PC directly connects to the switch, you have to setup the same subnet mask for PC and the switch. Default values of the managed switch are listed as followsIP Address| 192.168.1.224
---|---
Subnet Mask| 255.255.255.0
DHCP Client
Username
Password| Enabled (On)
Username admin
Password admin - After configuring correct IP address on your PC, open your web browser and access switch’s IP address.
The home page of Vigor Switch will be shown as below:
Customer Service
If the switch cannot work correctly after trying many efforts, please contact
your dealer for further help right away. For any questions, please feel free
to send e-mail to support@draytek.com.
Be a Registered Owner
Web registration is preferred. You can register your Vigor router via
https://myvigor.draytek.com.
Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all switches will be
regularly upgraded. Please consult the DrayTek web site for more information
on newest firmware, tools and documents. https://www.draytek.comb
GPL Notice
This DrayTek product uses software partially or completely licensed under the
terms of the GNU GENERAL PUBLIC LICENSE. The author of the software does not
provide any warranty. A Limited Warranty is offered on DrayTek products. This
Limited Warranty does not cover any software applications or programs.
To download source codes please visit: http://gplsource.draytek.com
GNU GENERAL PUBLIC LICENSE: https://gnu.org/licenses/gpl-2.0
Version 2, June 1991
For any question, please feel free to contact DrayTek technical support at
support@draytek.com for further information.
EU Declaration of Conformity
We DrayTek Corp. , office at No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan , R.O.C., declare under our sole responsibility that the product
- Product name: 8 Gbe Ports Switch
- Model number: VigorSwitch G1085
- Manufacturer: DrayTek Corp.
- Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan
is in conformity with the relevant Union harmonisation legislation:
EMC Directive 2014/30/EU , Low Voltage Directive 2014/35/EU and RoHS
2011/65/EU with reference to the following standards
Standard | Version / Issue date |
---|---|
EN 55032 | 2012+AC:2013 class A |
EN 61000-3-2 | 2014 Class A |
EN 61000-3-3 | 2013 |
EN 55035 | 2017 |
EN 62368-1 | 2014 +A11:2017 (Second Edition) |
EN 55032 | 2012+AC:2013 class A |
Hsinchu | October 3, 2019 |
--- | --- |
(place) | (date) |
Declaration of Conformity
We DrayTek Corp. , office at No.26, Fushing Rd., Hukou, Hsinchu Industrial
Park, Hsinchu 303, Taiwan , R.O.C., declare under our sole responsibility that
the product
- Product name: 8 GbE Ports Switch
- Model number: VigorSwitch G1085
- Manufacturer: DrayTek Corp.
- Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan
- Importer: CMS Distribution Ltd: Bhola Road, Kiltimagh, Co Mayo, Ireland
is in conformity with the relevant UK Statutory Instruments:
The Electromagnetic Compatibility Regulations 2016 (SI 2016 No.1091), The
Electrical Equipment (Safety) Regulations 2016 (SI 2016 No.1101), and The
Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012 (SI 2012 No. 3032) with reference to the
following standards:
Standard | Version / Issue date |
---|---|
EN 55032 | 2012+AC:2013 class A |
EN 61000-3-2 | 2014 Class A |
EN 61000-3-3 | 2013 |
EN 55035 | 2017 |
EN 62368-1 | 2014 +A11:2017 (Second Edition) |
EN 55032 | 2012+AC:2013 class A |
Hsinchu | October 3, 2019 |
--- | --- |
(place) | (date) |
Copyrights
© All rights reserved. This publication contains information that is protected
by copyright. No part may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language without written permission
from the copyright holders.
Trademarks
The following trademarks are used in this document:
- Microsoft is a registered trademark of Microsoft Corp.
- Windows, 8 , 10 and Explorer are trademarks of Microsoft Corp.
- Apple and Mac OS are registered trademarks of Apple Inc.
- Other products may be trademarks or registered trademarks of their respective manufacturers.
Safety Instructions
- Read the installation guide thoroughly before you set up the switch.
- The switch is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the switch yourself.
- Do not place the switch in a damp or humid place, e.g. a bathroom.
- Do not stack the switches.
- The switch should be used in a sheltered area, within a temperature range of +5 to +40 Celsius.
- Do not expose the switch to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.
- Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.
- Keep the package out of reach of children.
- When you want to dispose of the switch, please follow local regulations on conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the switch will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore- store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- **** Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device may accept any interference received, including interference that may cause undesired operation.
USA Local
Representative| Company name| ABP International Inc.
---|---|---
Address| 13988 Diplomat Drive Suite 180 Dallas TX 75234
ZIP Code| 75234| E-mail| rmesser@abptech.com
Contact Person| Mr. Robert Messer| Tel.| 19728311600
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. More updates, please visit www.draytek.com.
References
- Home | DrayTek
- GNU General Public License v2.0 - GNU Project - Free Software Foundation
- MyVigor - DrayTek
- Home | DrayTek
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>