DrayTek VigorSwitch Q2200x L2+ Managed Switch User Guide

June 3, 2024
DrayTek

VigorSwitch Q2200x L2+ Managed Switch
Quick Start Guide
Version: 1.0 Firmware Version: V2.7.1
(For future update, please visit DrayTek web site) Date: July 6, 2022

Package Content

DrayTek VigorSwitch Q2200x L2 Managed Switch - fig

The type of the power cord depends on the country that the switch will be installed.DrayTek VigorSwitch Q2200x L2 Managed Switch - fig
1

If any of these items is found missing or damaged, please contact your local supplier for replacement.

Panel Explanation

DrayTek VigorSwitch Q2200x L2 Managed Switch - Panel
Explanation

LED Status Explanation
Monitor On (Red) An alert for system failure due to overheating or wrong

voltage.
Off| The device is in normal condition and running normally.
SYS| On (Green)| The switch finishes system booting and the system is ready.
Blinking (Green)| The switch is powered on and starts system booting.
Off| The power is off or the system is not ready / malfunctioning.
PWR| On (Green)| The device is powered on and running normally.
Off| The device is not ready or is failed.
Port 1 ~ 16 (2.5GbE RJ45)| On (Green)| The device is connected with 2500Mbps.
On (Amber)| The device is connected with 10/100/1000Mbps.
Blinking| The system is sending or receiving data through the port.
Off| The port is disconnected or the link is failed.
Port 17 ~ 20 (SFP+)| On (Green)| The device is connected with 1000Mbps.
On (Blue)| The device is connected with 10Gbps.
Blinking| The system is sending or receiving data through the port.
Off| The port is disconnected or the link is failed.
Interface| Description
Port 1 ~ 16 (2.5GbE RJ45)| Used for Ethernet connection (10/100/1000/2500Mbps).
Port 17 ~ 20 (SFP+)| Port 17 to Port 20 are used for fiber connection.
Console| Used to perform telnet command control.
| Power inlet for AC input (100~240V/AC, 50/60Hz).

Hardware Installation

This section will guide you to install the switch through hardware connection and configure the switch’s settings through web browser.
3.1 Network Conection
Before starting to configure the device, you have to connect your devices correctly.
A hierarchical network with minimum levels of devices may reduce the timing delay between server and client station. Basically, this approach will minimize the number of  devices in any one path; will lower the possibility of network loop, and will improve network efficiency. If more than two devices are connected in the same network, select  one device as a Level 1 device and connect all other devices to it at Level 2. Server/Host is recommended to connect to the Level 1 device. This is generally if no VLAN or  other special requirements are applied. All device ports are in the same local area network.

DrayTek VigorSwitch Q2200x L2 Managed Switch - Network
Connection

3.1    Rack-Mounted Installation
The switch can be installed easily by using rack mount kit.

  1. Fasten the rack mount kit on both sides of the VigorSwitch using specific screws. DrayTek VigorSwitch Q2200x L2 Managed Switch - Mounted
  2. Then, install the VigorSwitch (with rack mount kit) on the 19-inch chassis by using other four screws.

DrayTek VigorSwitch Q2200x L2 Managed Switch - Mounted
1

Software Configuration

VigorSwitch, for example:

IP Address: 192.168.1.224
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.254

DrayTek VigorSwitch Q2200x L2 Managed Switch - Software
Configuration

Assign a reasonable IP Address, for example:

IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.254

Before using the switch, perform the following steps:
1. Set up a physical path between the configured the switch and a PC by a qualified UTP Cat. 5e cable with RJ-45 connector.
If a PC directly connects to the switch, you have to setup the same subnet mask for PC and the switch. Default values of the managed switch are listed as follows:

IP Address 192.168.1.224
Subnet Mask 255.255.255.0
DHCP Client Enabled (On)
Username admin
Password admin

2. After configuring correct IP address on your PC, open your web browser and access switch’s IP address. DrayTek VigorSwitch Q2200x L2 Managed Switch -
fig 2

The home page of VigorSwitch will be shown as below:DrayTek VigorSwitch
Q2200x L2 Managed Switch - fig 3

Customer Serice

If the switch cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com

GPL Notice
This DrayTek product uses software partially or completely licensed under the terms of the GNU GENERAL PUBLIC LICENSE. The author of the software does not  provide any warranty. A Limited Warranty is offered on DrayTek products. This Limited Warranty does not cover any software applications or programs.
To download source codes please visit: http://gplsource.draytek.com
GNU GENERAL PUBLIC LICENSE: https://gnu.org/licenses/gpl-2.0
Version 2, June 1991
For any question, please feel free to contact DrayTek technical support at support@draytek.com for further information.

Intellectual Property Rights (IPR) Information

Copyrights
© All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders.

Trademarks
The following trademarks are used in this document:

  • Microsoft is a registered trademark of Microsoft Corp.
  • Windows 8, 10 and Explorer are trademarks of Microsoft Corp.
  • Apple and Mac OS are registered trademarks of Apple Inc.
  • Other products may be trademarks or registered trademarks of their respective manufacturers.

Safety Instructions and Approval

Safety Instructions

  • Read the installation guide thoroughly before you set up the switch.
  • The switch is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the switch yourself.
  • Do not place the switch in a damp or humid place, e.g. a bathroom.
  • The switch should be used in a sheltered area, within a temperature range of +5 to +45 Celsius.
  • Do not expose the switch to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.
  • Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.
  • Keep the package out of reach of children.
  • When you want to dispose of the switch, please follow local regulations on conservation of the environment.

Warranty
We warrant to the original end user (purchaser) that the switch will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

EU Declaration of Conformity

We DrayTek Corp. , office at No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan , R.O.C., declare under our sole responsibility that the product

Product name:  16-port 2.5G with 4-port 10G SFP+ up-link Switch
Model number: VigorSwitch Q2200x
Manufacturer: DrayTek Corp.
Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303,

Taiwan

is in conformity with the relevant Union harmonisation legislation:
EMC Directive 2014/30/EU , Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU with reference to the following standards

Standard Version / Issue date
EN 55032 2015+AC:2016 class A
EN 61000-3-2 2014 Class A
EN 61000-3-3 2013
EN 55035 2017
EN 62368-1 2014 +A11:2017
EN IEC63000:2018 2018

Hsinchu (place)
December 30, 2020 (date) Calvin Ma / President
(Legal Signature)

Declaration of Conformity

We DrayTek Corp. , office at No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan , R.O.C., declare under our sole responsibility that the product

Product name: 16-port 2.5G with 4-port 10G SFP+ up-link Switch
Model number: VigorSwitch Q2200x
Manufacturer: DrayTek Corp.
Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303,

Taiwan
Importer:| CMS Distribution Ltd: Bohola Road, Kiltimagh, Co Mayo, Ireland

The Electromagnetic Compatibility Regulations 2016 (SI 2016 No.1091), The Electrical Equipment (Safety) Regulations 2016 (SI 2016 No.1101), and The Restriction of the  Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (SI 2012 No. 3032) with reference to the following standards:

Standard Version / Issue date
EN 55032 2015+A1:2016 class A
EN 61000-3-2 6-Jul
EN 61000-3-3 2013+A1:2019
EN 55024 2010+A1:2015
EN 62368-1 2014+A11:2017
EN IEC 63000:2018 2018

Hsinchu (place)
December 30, 2020 (date) Calvin Ma / President
(Legal Signature)

Regulatory Information

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device may accept any interference received, including interference that may cause undesired operation.
    Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

More update, please visit www.draytek.com.
USA Local Representative
Company name ABP International Inc.
Address 13988 Diplomat Drive Suite 180 Dallas TX 75234 , ZIP Code 75234
E-mail rmesser@abptech.com
Contact Person Mr. Robert Messer
Tel. 19728311600

Be a Registered Owner
Web registration is preferred. You can register your Vigor switch via https://myvigor.draytek.com.

Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all switches will be regularly upgraded.
Please consult the DrayTek web site for more information on newest firmware, tools and documents. https://www.draytek.com

Version: 1.0
Firmware Version: V2.7.1
(For future update, please visit DrayTek web site)
Date: July 6, 2022

Documents / Resources

| DrayTek VigorSwitch Q2200x L2+ Managed Switch [pdf] User Guide
VigorSwitch Q2200x L2 Managed Switch, VigorSwitch, Q2200x L2 Managed Switch, Q2200x L2, Q2200x Managed Switch, Managed Switch, Q2200x Switch, Switch
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals