DrayTek VigorAP 906 802.11ax Access Point User Guide
- May 15, 2024
- DrayTek
Table of Contents
- DrayTek VigorAP 906 802.11ax Access Point
- Product Usage Instructions
- Safety Instructions and Approval
- Panel Explanation
- Installation
- Connection and Configuration
- Connected As a Mesh Node (in Mesh Network)
- Customer Service
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DrayTek VigorAP 906 802.11ax Access Point
Specifications
- Product Name : VigorAP 906 802.11ax Access Point
- Firmware Version : V1.4.9
- Date : August 21, 2023
- Frequency Information :
- 2.4GHz WLAN : 2400MHz – 2483MHz, max. TX power: 19.81dBm
- 5GHz WLAN :
- 5150MHz – 5350MHz, max. TX power: 22.70dBm
- 5470MHz – 5725MHz, max. TX power: 29.47dBm
Product Usage Instructions
Safety Instructions and Approval
- Before setting up the device, read the installation guide thoroughly.
- Do not attempt to open or repair the device yourself.
- Avoid placing the device in damp or humid environments.
- Operate the device within a temperature range of 0 to +45 Celsius.
- Avoid exposing the device to direct sunlight or other heat sources.
- Do not stack the devices.
- Disconnect the Internet connection before powering off the device for configuration saving or firmware upgrades.
- Keep the device in a sheltered area and out of reach of children.
Warranty
Contact the manufacturer for warranty information.
Declaration of Conformity
The product complies with Directive 2014/53/EU and Regulation SI 2017 No. 1206.
FAQ
- Q: Can the VigorAP 906 be used outdoors?
- A : It is recommended to use the device in a sheltered area within the specified temperature range and not expose it to direct sunlight or moisture.
- Q: What is the warranty coverage for the VigorAP 906?
- A : For warranty information, please contact DrayTek Corporation.
Intellectual Property Rights (IPR) Information
Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders
Trademarks : The following trademarks are used in this document:
- Microsoft is a registered trademark of Microsoft Corp.
- Windows, Windows 8, 10, 11, and Explorer are trademarks of Microsoft Corp.
- Apple and Mac OS are registered trademarks of Apple Inc.
- Other products may be trademarks or registered trademarks of their respective manufacturers
Safety Instructions and Approval
Safety Instructions
- Read the installation guide thoroughly before you set up the device.
- The device is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the device yourself.
- Do not place the device in a damp or humid place, e.g. a bathroom.
- Do not stack the devices.
- The device should be used in a sheltered area, within a temperature range of 0 to +45 Celsius.
- Do not expose the device to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.
- Do not deploy the cable for LAN connection outdoors to prevent electronic shock hazards.
- Do not power off the device when saving configurations or firmware upgrades. It may damage the data in a flash. Please disconnect the Internet connection on the device before powering it off when a TR-069/ ACS server manages the device.
- Keep the package out of reach of children.
- When you want to dispose of the device, please follow local regulations on the conservation of the environment.
Warranty
We warrant to the original end-user (purchaser) that the device will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore- store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects that do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revisions or changes.
Declaration of Conformity
Hereby, DrayTek Corporation declares that the radio equipment type VigorAP 906 is in compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the
following internet address:
https://fw.draytek.com.tw/VigorAP 906/Document/CE/
Manufacturer : DrayTek Corp.
Address : No. 26, Flushing Rd, Hukou, Hsinchu Industrial Park, Hsinchu
303, Taiwan
Product : VigorAP 906
Frequency Information for the European area
1: for 2.4GHz WLAN model; 2: for 5GHz WLAN model)
This product is designed for 2.4GHz and 5GHz WLAN networks throughout the EC
region.
Declaration of Conformity
Hereby, DrayTek Corporation declares that the radio equipment type VigorAP 906 is in compliance with Regulation SI 2017 No. 1206.
- Manufacturer : DrayTek Corp.
- Address : No. 26, Fushing Rd, Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan
- Product : VigorAP 906
Frequency Information for UK area
(1: for 2.4GHz WLAN model; 2: for 5GHz WLAN model)
This product is designed for 2.4GHz and 5GHz WLAN network use in the UK &
Ireland.
Caution
- Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
- This equipment complies with CE RF radiation exposure limits set forth for an uncontrolled environment.
- This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
- Operations in the 5.15-5.35GHz band are restricted to indoor usage only.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device may accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body
*The external power supply used for each product will be model dependent.
For more updates, please visit www.draytek.com.
Package Content
Take a look at the package content. If there is anything missing or damaged, please contact DrayTek or the dealer immediately.
Note
- The antenna/transmitter should be kept at least 20 cm away from the human body.
- The maximum power consumption is 18 watts.
Panel Explanation
Installation
This section will guide you to install the AP through a hardware / wall-
mounting connection.
For hardware connection, refer to the following steps to connect your devices
correctly.
- Connect VigorAP 906 to the xDSL modem, router, or switch/hub in your network through the LAN B port of the access point by Ethernet cable. You can also connect VigorAP 906 to a Vigor router via the wireless connection.
- For detailed information, refer to the VigorAP 906 User’s Guide.
- Connect a computer to another available LAN A port. Make sure the subnet IP address of the PC is the same as the VigorAP 906 management IP, e.g.,192.168.1.X.
- Connect the A/C power adapter to the wall socket, and then connect it to the PWR connector of the access point.
- Power on VigorAP 906.
- Check all LEDs on the front and back panel. The ACT LED on the front panel should blink; the WAN/LAN LED on the back panel should be on if the access point is correctly connected to the xDSL modem, router or switch/hub.
For wall mounting, refer to the following steps.
- Drill two holes on the wall. The distance between the holes shall be 100.75mm. The recommended drill diameter shall be 6.5mm (1/4”).
- Fit screws into the wall using the appropriate type of screw plug.
- Hang the VigorAP directly onto the screws.
Connection and Configuration
This section will guide you to configure AP settings to establish the wireless network through a web browser.
1. Make sure your PC connects to the device correctly.
2. Open a web browser on your PC and type http://192.168.1.2. A pop-up window
will open to ask for a username and password. Pease type “admin/admin” on
Username/Password and click Login.
Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be in the same subnet as the IP address of VigorAP 906.
- If there is no DHCP server on the network, then VigorAP 906 will have an IP address of 192.168.1.2.
- If there is DHCP available on the network, then VigorAP 906 will receive its IP address via the DHCP server.
- If you connect to VigorAP by wireless LAN, you could try to access the web user interface through http://vigorap.com.
Connected As a Mesh Node (in Mesh Network)
- Install VigorAP on the place you want.
- As a mesh node, settings related to VigorAP 906 must be configured by a remote Mesh Root (e.g., VigorAP 906) within the mesh network. The user must detect VigorAP 906 via a Mesh Root to add it as a mesh node.
Connected As an Access Point
As an access point, VigorAP 906 must be connected to a router and configured in the operation mode.
- Connect VigorAP to a Vigor router.
- Use a twisted-pair cable with RJ-45 plugs at both ends and plug into the Ethernet device (e.g., Vigor router) and Ethernet port of VigorAP.
- There are two methods to configure VigorAP.
- Method 1:
- (a ) First, open a web browser on your PC and type https://192.168.1.2. A pop-up window will open to ask for a username and password.
- (b) After clicking Login, the Quick Start Wizard for configuring wireless settings will appear as follows.
- (c) Follow the on-screen steps to finish the network connection.
Method 2:
- (a) Use a mobile phone to scan the QR code named with the DrayTek Wireless App to download the DrayTek Wireless APP.
(b) After downloading, run the APP.
(c) From the home page, click the Connect icon to access the Connect
page. Next, press the QR code icon next to the Scan QR Code on your phone
screen to open the camera.
Scan the QR code-named with Connect SSID to access the web user interface
(configuration wizard) of VigorAP 906. (For iOS users, the SSID and the
password will be shown first. Simply click the Connect button to access the
web user interface of VigorAP.)
Customer Service
If the device cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send an e-mail to “support@draytek.com”.
Be a Registered Owner
Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com.
Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek website for more information on
newest firmware, tools, and documents.
https://www.draytek.com
GPL Notice This DrayTek product uses software partially or completely licensed under the terms of the GNU GENERAL PUBLIC LICENSE. The author of the software does not provide any warranty. A Limited Warranty isoffered on DrayTek products. This Limited Warranty does not cover any software applications or programs.
To download source codes please visit: http://gplsource.draytek.com
GNU GENERAL PUBLIC LICENSE: https://gnu.org/licenses/gpl-2.0
Version 2, June 1991
For any questions, please feel free to contact DrayTek technical
support at
- support@draytek.com for further information.
References
- Home | DrayTek
- GNU General Public License v2.0 - GNU Project - Free Software Foundation
- MyVigor - DrayTek
- Home | DrayTek