Westinghouse 012822 18W 3500K T8 U-Bent Linear LED Light Bulb Owner’s Manual

June 13, 2024
Westinghouse

W-748 012822
Owner’s Manual
Westinghouse W-748 18W 4000K T8 Dimmable U Bent Linear LED Light
BulbWestinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
Used under license by Westinghouse Lighting.
www.westinghouselighting.com ting.
All Rights Reserved.
and Westinghouse are trademarks of Westinghouse Electric Corporation.
Made in China

Product Features:

  • UL certified
  • Full glass housing: No Aging, Yellowing, Bending

Product Applications:

Widely used in residential buildings, offices, shopping malls, supermarkets, hosptials, assembly lines, warehouses, etc. for energy saving illumination.

Installation Instructions:

Please completely comply with this instructions and notes, to ensure that the product is operated in a safe condition.

**** Safety Precautions:

For your and other safety please read the precaution carefully before installation:

  1. Product should be installed by qualified electrician.
  2. Switch off the power supply before commencing work, make sure correct connection before you power on.
  3. Do not apply uncertified LED driver with the product.
  4. NOT FOR EMERGENCY LIGHTING.

Wiring Instructions – Electronic Ballast

Retrofit luminaire with 1 lampWestinghouse W-748 18W 4000K T8 Dimmable U
Bent Linear LED Light Bulb - Electronic BallastRetrofit luminaire with 2 lamps Westinghouse W-748 18W 4000K T8 Dimmable U Bent Linear LED Light Bulb -
Electronic Ballast 1Retrofit luminaire with 4 lamps Westinghouse W 748 18W 4000K T8 Dimmable U Bent Linear LED Light Bulb
-

DIMMING FUNCTION

This tube can be achieve 0-10V dimming when installed in combination with dimming module (Westinghouse Lighting model 502606930). One dimming module can only operate one LED tube. Westinghouse W 748 18W 4000K T8 Dimmable U Bent
Linear LED Light Bulb - DIMMING FUNCTIONWARNING:
Only use the control provided with or specified by these instructions to control this lamp. This lamp will not operate properly when connected to a standard (incandescent) dimmer or dimming control.
Only operate with specific dimming module 502606930 manufactured by Westinghouse.
Type B LAMP – intended for operation in luminaires with traditional fluorescent-type lamp holders wired directly to the branch circuit. This includes both factory-wired luminaries as well as those converted for this purpose under a retrofit program.
Risk of fire or electric shock. Installation of this Retrofit Kit requires knowledge of electrical systems. If you are not qualified , do not attempt installation, and contact a qualified electrician.
Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
To prevent damage to wiring, do not expose wires to the edges of sheet metal or other sharp objects.
To avoid potential fire or shock hazard, do not use this retofit kit in luminaires employing shunted bi-pin lampholders. Note: Shunted lamp holders are found only in fluorescent luminaires with Instant-Start ballasts. Instant- Start Ballasts can be identified by the words “Instant Start” or “I.S.” marked on ballast. This designation may be in the form of a statement pertaining to the ballast itself, or may be combined with the marking for the lamps with which the ballast is intended to be used, for example F40T12/IS. For more information, contact the LED luminaire retrofit kit manufacturer.
Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals. Instead installers should cut existing lampholder leads away from the ballast and make new electrical connections to lampholder lead wires by employing applicable connectors.
WARNING- Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.
THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY UL OR AUTHORITIES HAVING JURSDICTION.
The units covered by this report were intended to retrofit surface mount without difiuser, Type IC or non-IC recessed mount Listed fluorescent luminaires that use maximum three tubular lamps, the minimum lamp compartment dimensions are listed below:

Model| MINIMUM LAMP COMPARTMENT DIMENSIONS
[Length x Width x Height][mm]
---|---
LED 18T8/UB6/DIM/XX Ballast Bypass| 605x604x81

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Westinghouse User Manuals

Related Manuals