Weller WHP 200 Infrared Preheating Plate User Manual

: June 13, 2024
: Weller

Table of Contents

Weller WHP 200 Infrared Preheating Plate
Description
Accessories
Technical data
Placing in operation
Error indications on the display
Power-on routine
PCB holder
Items supplied
Wiring
Disposal
Declaration of conformity
Product Registration
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Weller WHP 200 Infrared Preheating Plate

We thank for the confidence you have shown by purchasing the Weller Heating Plate WHP 200. During manufacture the strictest quality requirements are applied; these assure the correct function of the device and make it possible to obtain optimal soldering results.

Attention!

Prior to placing the device in operation, please carefully read these operating instructions and the safety instructions enclosed. If the safety instructions are not observed, there is a risk of injury.
The manufacturer accepts no liability for usage other than that described in the operating instructions or for unautho-rised modifications
The WELLER heating plate WHP 200 complies with the EU declaration of conformity as per the essential safety requirements in the directives 2004/108/EU and 2006/95/EU.

Description

The WHP 200 heating plate is equipped with a 200 W infrared high-temperature lamp and enables the user to pre-heat electronic assemblies in numerous ways. The high-temperature lamp supplies energy primarily in the wave-length range of 2 – 10 μm and heats modern tools quickly and efficiently. Digital regulation electronics ensure precise temperature behaviour.

$Weller-WHP-200-Infrared-Preheating-Plate-fig- $2$$

Display (3-digit 7-segment display)
“UP” button
Mains switch
“DOWN” button
Optical indication of the state of regulation
Mains connection

Accessories

Easy fix board holder

Code No.: T0058757875

Technical data

Dimensions: (W x L x H)
- 165 x 195 x 70 mm
- 6,5 x 7,68 x 2,75 inch
Mains voltage: 230 V (120 V); 50 Hz (60 Hz)
Power: Heating zone 200 W
Temperature range: 50°C – 400°C (150°F – 750°F)
Protection class: 1
Heating zone: 120 (4,72) x 60 (2,36) mm (inch)

Placing in operation

Remove all temperature sensitive and flammable objects from the vicinity of the heating plate. Ensure that the heating plate is switched off. Ensure that the mains voltage is cor-rect. Connect the device to the mains (6). Switch on the device at the mains switch (3). When the device is switched on, a self- test is performed during which all display ele-ments (1) are operated. The temperature set (setpoint) and the temperature scale (°C / °F) are then displayed briefly. The display then switches automatically to the indication of the actual value. The red dot on the display illuminates (5). This dot is a visual indication of the state of the regulation. Continuous illumination indicates the system is warming up.

Flashing indicates that the operating temperature has been reached.

Adjusting temperature
The digital display (1) normally indicates the actual temper-ature. The digital display (1) switches to the current setpoint when the ”UP” or “DOWN” button (2)(4) is pressed. The set-point (flashing indication) can now be changed as required by pressing or pressing and holding the “UP” or “DOWN” button (2)(4). If the button is pressed and held down, the set-point changes quickly. Approx. 2 sec. after the button is released, the digital display (1) automatically switches back to the actual value.

Manual heating shut down (OFF)
The device heating is shut down by simultaneously pressing the “UP” and “DOWN” buttons. “Off” appears on the display (1).

Error indications on the display

Error indications on the display (1)

– – – No temperature sensor detected
E10 Maximum housing temperature exceeded

Power-on routine

°C / °F change over
For this purpose the device is first switched off at the mains switch (3). Press DOWN button (4) and switch on the device. Keep button pressed until the “°F” appears on the dis-play (1). When the “DOWN” button is released the setting is saved. Use the same procedure for the change over to “°C”.

PCB holder

The PCB holder is secured to the housing upper section by the Heizone. For securing, removing or adjusting the PCB holder, release the knurled screws.

Items supplied

WHP 200 heating plate
Mains cable
PCB holder
Operating instructions
Safety information

Wiring

Gesamtschaltplan WHP 200

$Weller-WHP-200-Infrared-Preheating-Plate-fig- $5$$

Subject to technical change without notice!
See the updated operating instructions at www.weller-tools.com.

Symbols

CE mark of conformity
British Conformity Mark

Disposal

Waste light sources have to be removed from equipment. Check with your local authority or retailer for recycling advice and collection point. According to local regulations retailers may have an obligation to take back waste electrical and electronic equipment free of charge. Your contribution to re- use and recycling of waste electrical and electronic equipment helps to reduce the demand of raw materials. Waste electrical and electronic equip-ment contain valuable, recyclable materials, which can adversely impact the environment and the human health, if not disposed of in an environmentally compatible manner. Delete personal data from waste equipment, if any.

Contaminated filters must be treated as special waste. Dispose of replaced equipment parts, filters or old devices in accordance with the rules and regulations applicable in your country.

Declaration of conformity

EC declaration of conformity
We hereby declare that the products described herein comply with the following guidelines:

UK declaration of conformity
We hereby declare that the products described herein e hereby declare that the products described herein comply with the following guidelines:comply with the following guidelines:

2014/35/EU, 2014/30/EU, 2006/42/EU
SI 2016 No.1101, SI 2016 No.1091, SI 2008 No.1597

Besigheim, 2023-08-28

Philippe Buidin
Managing director

Authorised to compile technical documentation. Apex Tool Group UK Ltd Registered in England, Company Number 14127816 Registered Office: 20 Farringdon Street, 8th Floor London, EC4A 4AB, United Kingdom.

Weller Tools GmbH
Carl-Benz-Straße 2, 74354 Besigheim, Germany.