Bright 025998 Magnetic Contact For Window/Door Instruction Manual
- June 13, 2024
- Bright
Table of Contents
025998 SMART
Instruction Manual
025998 Magnetic Contact For Window/Door
MAGNETIC CONTACT
Operating instructions (Translation of the original instructions)
Important! Read the user instructions carefully before use. Save them for
future reference. Jula reserves the right to make changes. For latest version
of operating instructions, see www.jula.com
© Jula AB, BOX 363, SE-532 24 SKARA
2023-05-05
https://smartapp.tuya.com/smartlife
SAFETY INSTRUCTIONS
SYMBOLS
| Read the instructions.
---|---
| Approved in accordance with the relevant directives.
| Recycle discarded product in accordance with local regulations.
TECHNICAL DATA
| Rated voltage, batteries | 2 x AAA |
|---|---|
| Frequency | 2.4 GHz |
| Protection rating | IP20 |
DESCRIPTION
DESCRIPTION
This is a SMART product that can be connected to existing WiFi and controlled
via the Smart Life app. Does not require separate hub/router. In the app you
can control all SMART products and use functions such as timer controlled,
scheduled and automated events.
SYSTEM REQUIREMENTS
Check that the smartphone is connected to the WiFi network 2.4 GHz and switch
on the bulb. WiFi router. iPhone, iPad (IOS 11.0 or higher) or Android (5.0 or
higher).
ASSEMBLY
- Install the sensor on the frame of the window or door.
- Install the magnet on the window or door.
IMPORTANT:
Only one side of the sensor reacts to the magnet. If the sensor is put on the
left, with the LED upwards, then the right side will be in contact with the
magnet. If the sensor is placed to the right of the magnet then the LED needs
to point downwards.
NOTE:
- The maximum distance between the sensor and the magnet must not exceed 10 mm.
- If there is a difference in height between the surfaces where the sensor and magnet are placed, this difference needs to be leveled out to achieve a sufficiently good signal.
USE
INSTALL APP
Scan the QR code to download the Smart Life app. Or search at App Store or
Google Play.
FIG. 1
Start the app to register, or log into your account.
Registration
Registration can be done using a mobile phone number or an email address.
*Country-specific settings follow the mobile phone system, but it is possible to manually change the country code/country settings before completing the registration (after completing the registration, changes cannot be made).
Log in
If you already have an account, click on ‘Log in with an existing account’
under ‘Create a new account’, enter the mobile phone number or email address
used for registration and enter the password to log in, after which the iOS
operating system can use the Apple ID for login.
CONNECT PRODUCT
-
Start the app Smart life and select “+”.
-
Select “Sensor” and search for “Contact Sensor” (WiFi).
-
Select 2.4 GHz WiFi network and enter password.
-
Select “Confirm” when the status lamp flashes rapidly.
-
When the above steps are completed, select “Blink Quickly”. Pairing of the
product and app takes place. -
Press the distribution button for 5 seconds until the green status light flashes quickly, then release the button.
FIG. 2 -
Select “Done” when the product has been successfully added.
-
Go to the main screen.
REPLACING BATTERIES
- Press the middle part of both long sides.
- Replace the batteries.
- Put back the cover in the same position it was in.
IMPORTANT:
When the cover has been lifted, take note of which side of the cover the pin
for the tamper protection is on. Incorrect placement of the cover can cause
the pin to break off. A broken pin will cause the tamper protection to sound
the alarm continuously.
EU DECLARATION OF CONFORMITY
Jula Item number
025998
Model no.:GS325W
Jula AB, Box 363, SE-532 24 SKARA, SWEDEN
This declaration of conformity is issued under the sole responsibility of the
manufacturer.
DOOR SENSOR
Conforms to the following directives, regulations and standards:
| Directive/Regulation | Harmonised standard |
|---|---|
| RED 2014/53/EU | 3(1)a EN IEC 62368-1:2020+A11, EN IEC 62311:2020, EN |
50665:2017
3(1)b ETSI EN 301489-1 V2.2.3, ETSI EN 301489-17 V3.2.4,
3(2) ETSI EN 300 328 V2.2.2
EN 50270:2015, EN 61000-6-3:2007+A1, EN IEC 61000-6-1:2019, EN 61000-6-1:2007,
EN
IEC 61000-3-2:2019, EN 61000-3-3:2013+A1
RoHS 2011/65/EU + 2015/863| EN 50581:2012
This product was CE marked in year:
Signed for and on behalf of
Skara 2023-03-14
Fredrik Bohman
BUSINESS AREA MANAGER
DoC: EN-SE-NO-PL-DE-FI-FR-NL
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>