Harper Bright Designs QMY061AAA Elegant Beige Twin Size Upholstered Wood Daybed Instruction Manual

Harper Bright Designs QMY061AAA Elegant Beige Twin Size Upholstered Wood Daybed Instruction Manual

Thank you for purchasing this quality product. Be sure to check all packing material carefully for small part that may have come loose inside the carton during shipment.

ASSEMBLY INSTRUCTIONS

PART LIST : WF295781

No.| Description| Sketch| Quanlity
A| Arm Panel L/R| | 2PCS
B| Bun Foot| | 4PCS
PART LIST : WF295782

No.| Description| Sketch| Quanlity
C| Headboard panel| | 1PC
D| Side Rail| | 2PCS
E| Center Support Slat| | 1PC
F| Slats Rolls| | 2SET
G| Trundle Cushion| | 2PCS
H| Trundle Side| | 2PCS
I| Trundle Back| | 1PC
J| Trundle Support Slat| | 1PC
HARDWARE LIST : WF295781

No.| Description| Sketch| Size| Quanlity
K| WasherSemicircle| | 0 g”25L| 4PCS
L| Thread Bolt| 13mmL| 0 3’2i”L| 8PCS
M| Flat Washer| | 0 An| 4PCS
N| Hexagonal Nut| | 0 a”8PCS|
0| Open Wrench| | M12| 1PC
P| Allen Key| | M424″L| 1PC
Q| Screw| | 0 81-i”L| 40PCS
Tools Required (not Provided)

Screwdriver

Step 1.
Assemble the Bun Foot(B) with the Armrest L/R(A) into pre-drilled holes on the bottom of Armrest. Please avoid overtightening. Besides, use the Thread Bolt(L), put onto pre-drilled holes nut and secure by hand.

L| Thread Bolt|
13mmL| Ø S “*2-3“L16         4| 4PCS
---|---|---|---|---

Step 2.
Before performing this step, please loosen the bolts of the Arm Control Panel L/R(A), intended to hook metal Rail(D) and metal center(E) securely set to the bolt. Besides, pay attention to also bring the Headboard panel(C) which has pre-drilled holes at both ends, to the L/R Arm(A) with two pre-assembled threaded rods, by using the Flat Washer (M), Hex Nut(N). Finally, tighten them with the Allen Key(P), the Open Wrench(O) as guide.

Step 3.
Note: before placing the pre-assemble clusters Slat roll(F) in the side rails(D), it is advisable to check the direction of the arrow, place it straight out ahead and arrange it neatly. Then, tighten they are by Screws(Q).

Step 4.
Assemble the Thread Bolt(L) put onto pre-drilled holes nut for both Trundle Cushion(G) and the inner face Trundle back(I),and secure by hand.

L| Thread Bolt|
13mmL| Ø S “*2-3“L16         4| 4PCS
---|---|---|---|---

Step 5.
Place the Trundle side plate(H) with mount wheels to put the back face Trundle Cushion(G) and the inner face Trundle back(I), which has four pre- assembled threaded rods, by using the Washer Semicircle(K), Hex Nut(N). Finally, tighten them with the Open Wrench(O) as guide

Step 6.
Place put the Trundle support slat(J) with mount wheels the into the Trundle side(H). Then, put the Slat roll(F) and arrange it neatly. Finally, all togethertighten they are by Screws(Q) as guide.

Step 7.
Push drawers under the bottom of Bed

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>